Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation . system, consult your navigation manual. To car light control switch Ignition key switch Car fuse box (Main fuse) –+ P.CONT MUTE ANT. CONT ILLUMI FRONT L FRONT R speaker REAR L REAR R FM/AM Fuse (10A) (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple To front left To front right speaker To rear right speaker To rear left speaker Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) ACC Car fuse box If no connections are made, do not let the wire come out from the tab. Rear right output (Red)/ Sub Woofer right output (Red) Power control wire (Blue/White) Motor antenna control wire (Blue) Dimmer control wire (Orange / White) film-type antenna. TEL mute wire (Brown) Battery English | 25 Installing the Escutcheon For General Motors 1 Refer to the section (page 28) and then remove the hard rubber frame. 2 Cut out accessory 2 to meet the shape of the opening of the center console. 3 Attach accessory 2 to the unit. Accessory2Cut out to meet the shape of the opening in the vehicle. For TOYOTA/ SCION 1 Refer to the section (page 28) and then remove the hard rubber frame. 2 Cut out accessory 2 as illustrated. . • When cutting out accessory 2, make sure it fits the opening of the center console. 3 Fold double-sided adhesive (accessory 3) along the slit and attach it to accessory 2 cut-out against the center rib as illustrated. Use 2 pieces of accessory 3 for 1 accessory 2 cut-out. 4 Attach accessory 2 cut-out to the unit. Cutting line Accessory2Accessory3 26 | English Installation Installing the Unit Screw (M4X8) Accessory6Firewall or metal support (commercially available) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Installing in Japanese-Made Cars and General Motors Cars Install onto the car bracket using the supplied screws (M5 . 6 mm, M5 . 7 mm). The holes of the car bracket to use will differ depending on the car model. Car Bracket Accessory4 (M5 . 7 mm) or Accessory5(M5 . 6 mm) English | 27 Removing the Unit Removing the Hard Rubber Frame (escutcheon) 1 Engage the catch pins on the removal tool 7 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 When the lower level is removed, remove the upper two locations. . • The frame can be removed from the top side in the same manner. Removing the Unit Accessory7Lock Catch 1 Refer to the section and then remove the hard rubber frame. 2 Remove the Hex-head screw with integral washer (M4X8) on the back panel. 3 Insert the two removal tools 7 deeply into the slots on each side, as shown. 4 Lower the removal tool towards the bottom, and pull out the unit halfway while pressing towards the inside. ¤ • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, carefully not to drop it. Accessory7 28 | English Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. ! Cannot switch to Aux source. ^ AUX is not turned on. . (page 20) ! • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter. ^ • Preout is not set to subwoofer. . (page 18) • (page 8) is not set to On. ! Cannot set up the subwoofer phase. ^ Low pass filter is set to Through. .
)
