Assessments - , GPA: ( )

Instruções de Operação Kenwood, Modelo KDV-C810

Fabricante : Kenwood
Arquivo Tamanho: 1.54 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

por este dispositivo também tem outras instruções :

CD Auto / DVD changer - KDV-C810 (1.39 mb)

CD Auto / DVD changer - KDV-C810 (1.29 mb)

After removing the transport screw, retain it carefully and attach it again before transporting the unit again. Cover the holes indicated by " 3" with the dustproof seals ! . The angle adjustment switches on the both side of the unit are to be set according to the angle of installation of the DVD/CD auto changer. Set both of the 4 switches to the same position. If the switches are not set properly, sound skip or other malfunction may occur. H V 45° H V 45° H V 45° H V 45° 3 3 3 3 “H” Set "H" for all the four angle adjustment parts on both sides. Cover the holes indicated by " 3"/" " with the dustproof seals ! , @ . Use the holes marked " . " to install the unit. Accessory 3 Accessory 4 Accessory 1 (R) (M5 x 8) (O5 x 12) Accessory 1 (L) O3.6 HV45° HV45° HV45° HV45° — 33 — 33— 33 — —— Installation English — 34 — ¦ Vertical installation H V 45° H V 45° H V 45° H V 45° 3 3 “V” ¦ At a 45° angle installation H V 45° H V 45° H V 45° H V 45° “45°” 3 3 Accessory 2 (R) Accessory 4 (M5 x 8) Accessory 3 (O5 x 12) Accessory 2 (L) Accessory 2 (R) Accessory 4 (M5 x 8) Accessory 3 (O5 x 12) Accessory 2 (L) O3.6 O3.6 Set "V" for all the four angle adjustment parts on both sides. Cover the holes indicated by "3"/" " with the dustproof seals !, @. Use the holes marked "." to install the unit. Changer control cable (Accessory7) Set "45°" for all the four angle adjustment parts on both sides. Cover the holes indicated by "3"/" " with the dustproof seals !, @. Use the holes marked "." to install the unit. ¦ ¦ Mounting the remote controller ¦ ¦ Mounting the remote controller H V 45° H V 45° H V 45° H V 45° 3 3 3 3 “H” Set "H" for all the four angle adjustment parts on both sides. Cover the holes indicated by " 3"/" " with the dustproof seals ! , @ . Use the holes marked " . " to install the unit. Accessory 1 (R) Accessory 4 (M5 x 8) Accessory 3 (O5 x 12) Accessory 1 (L) O3.6 Accessory 9 Accessory $ Light detector of remote controller (Accessory8) Accessory $ (M3 x 8 mm) Accessory # Clear the surface to be affixed with accessories0. — 35 — English English What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery wire. . The remote controller does not work. . See (page 30) to connect the light detector of the remote controller correctly. ? The power cannot be turned off . You select the source mode of this machine, which is connected to a center unit. . The power cannot be turned off because the center unit is under operation. If changing a mode other than the source mode of this machine on the center unit, you can turn off the power. ? The power is automatically turned off. . You switched the source mode while connecting to a center unit. . If selecting the source mode of this machine on the center unit and then switching to a mode other than this machine, you turn off the power. ? No video image appears. . The unit is not connected to the parking brake detection . Make proper connections according to . . The parking brake is not engaged. . For safety reasons no video images are vehicle is moving. Engaging the parking to be displayed. . The setting of the NTSC/PAL switch is incorrect. . Set the NTSC/PAL switch correctly. ? Nothing happens when . The " " symbol appears in . You cannot carry . The batteries . Replace both two batteries of the remote controller with new ones. . The remote controller does not work. . See to connect the light detector of the remote controller correctly. . A center unit not applicable is connected. . See (page 4). ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on . . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? No sound can be heard, or the volume is low. . The audio setting of audio output is not “ANALOG”. . If connecting through a center unit or RCA cable, select “ANALOG” for this setting. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on . ? The specified disc does not play, but another one plays instead. . The specified DVD/CD is quite dirty. . Clean the Disc. . The disc is upside down. . Set the disc with the label face downward. . The disc is severely scratched. . Try another disc i...