Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
You can damage both your unit and the CD changer if you connect them incorrectly. — 3— Safety precautions Safety precautions NOTE • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer. • Press the reset button if the Disc auto changer fails to operate correctly. Normal operation should be resloved. Reset button • Characters in the LCD may become difficult to read in temperatures below 41 °F (5 °C). • The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations the display may represent something impossible in actual operation. Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth. Cleaning the Unit If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off. Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters. About Cassette tape Cleaning the tape head When there’s noise or the sound quality is bad during tape play the tape head maybe dirty, clean the tape head. About Cassette tape • If the tape is slack tighten it. • If the cassette tape label is peeling on again. • Don’t use deformed cassette • Don’t place cassette tape on etc. where the temperature • Don’t use cassette tape 100 minutes long or longer. — 4— General features General features Release button Turning ON the Power SRC/ CLK/ Press the [SRC] button. u PWR OFF ADJ 4 FM . Turning OFF the Power Press the [PWR OFF] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display d Tuner "TUnE" ATT/ #1 - 5 AUD/ AM LOUD A.ADJ Tape "TAPE" External disc "DISC" Standby (Illumination only mode) "OFF" ATT indicator Clock display LOUD indicator Clock indicator — 5— General features General features Volume Increasing Volume Press the [ u] button. Decreasing Volume Press the [ d] button. Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. Loudness Compensating for low and high tones during low Press the [LOUD] button for at least 1 second. Each time the button is pressed for at least 1 second Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON. dB (Sound Coordinate) You can recall the best sound the music. 1 Select the source Press the [SRC] 2 Enter Control mode Press the [AUD] button. 3 Select the Sound type Press the [#1] — [#5] button. Press button Sound setting Display [#1] Flat "DB-1" [#2] Rock "DB-2" [#3] Pops/ Top40 "DB-3" [#4] Jazz "DB-4" [#5] Easy "DB-5" When the dB(Sound Coordinate) setting is changed, the Bass and Treble set in audio control replace the dB(Sound Coordinate) values. 4 Exit Control mode Press the [AUD] button. Audio Control 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [A.ADJ] button for at least 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed switch as shown below. 4 Adjust the Audio item Press the [ 4] or [ . ] button. — 6— Adjustment Item Bass level Treble level Balance Adjustment Item Bass level Treble level Balance Range –4 — 4 –4 — 4 L15 — R15 The faceplate of the unit can be detached and taken with you, helping to deter theft. Fader "FD" R15 — F15 Removing the Faceplate Theft Deterrent Faceplate 5 Exit Audio Control mode Press the [A.ADJ] button. Switching Clock Display Switching the displayed information. Press the [CLK] button. Each time the button is pressed it switches between clock display and current source. During clock display the clock indicator is ON. Adjusting Clock 1 Select the clock display Press the [CLK] button. 2 Enter clock adjustment mode Press the [CLK] button for at least The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit clock adjustment Press the Press the Release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattach...
Este manual também é adequado para os modelos :Unidade - KRC-265 (264.59 kb)