Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
• If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the faceplate does not hit the lid when closing and — 14 — Connecting Wires to Terminals Connecting Wires to Terminals Pin Numbers for ISO Connectors Cable Color Functions External Power Connector A–4 A–5 A–7 A–8 Yellow Blue/White Red Black Battery Power Control Ignition (ACC) Earth (Ground) Connection Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) Fuse (10A) — 15 — 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 TEL MUTE P.CONT ANT.CONT Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input (Accessory3) Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) control terminal when using or to the antenna control terminal in the vehicle. conversation. A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Antenna Conversion Adaptor (ISO–JASO) Antenna Cord (ISO) Connect to the terminal that is grounded when either the telephone rings or during To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power the optional power amplifier, English English 2WARNING Connecting the ISO Connector (see p.15) The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector connected to anything, while the A-7 pin (red) constant power supply (or both the A-7 (red) are connected to the constant power supply). Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) When the connection is made 3 above, the unit's power will be linked to the ignition For that reason, always off the unit's power To link the unit's power (ACC...red) to ignition key. Installation ¦ Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Screw (M4X8) (commercially available) — 16 — 16— 16 — —— Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (eg, the sound may skip). Installation Installation Removing the hard rubber frame ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then 1 Engage the catch pins on the removal tool and remove the two remove the hard rubber frame. locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 Remove the screw (M4.8) on the back panel. Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) 4 Lower the removal tool out the unit halfway while toward the bottom, and pull pressing towards the inside. Accessory2 Removal tool Be careful to avoid injury from the catch pins 5 Pull the unit all the way out with your hands, being The frame can be removed from careful not to drop it. — 17 — 17— 17 — —— English English What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . Afte...
Este manual também é adequado para os modelos :Unidade - KRC-2904G (1.04 mb)