Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
• When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. — 16 — Connecting Connecting Rear left output (White) P.CONT ANT. CONT. FRONT • L FRONT • R REAR • L REAR • R – + FM/AM antenna input Rear right output (Red) Fuse (10A) Wiring harness (Accessory1) White/Black Gray/Black Purple/Black White Gray Green Purple To front left speaker To front right speaker To rear right speaker To rear left speaker Power control/Motor antenna control wire (Blue/White) Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch ACC Car fuse box Battery If no connections are made, do not let the wire come out from 4 Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Front left output (White) Front right output (Red) To connect the Disc changer, consult your Disc changer manual. Green/Black Car fuse box (Main fuse) — 17 — Installation Installation ¦ Installation Firewall or metal support Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installing in 1 Refer to the section and then remove the hard 2 Align the holes in the unit vehicle mounting bracket and screws. T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 Never insert the taptite screw (o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 18 — ¦ ¦ 1 Engage the catch pins locks on the lower level. Lower the frame and pull Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner. ¦ Removing the 1 Refer to the section remove the hard rubber 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 19 — English English What might just be the result Before calling service, for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? The sound quality . One of the speaker . Check the speaker wiring. . The tape head is dirty. . Clean the tape head. . The speakers are not wired correctly. . Reconnect the speaker wires so that connected to a different speaker. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. Tuner source ? Radio reception is poor. . The car antenna is not extended. ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't swhich to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on