Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate: 1 Hold the faceplate so that the control panel faces the front toward you and set the left side of the faceplate in the faceplate bracket. NOTE The panel cannot be reversed when the faceplate Opening the control panel: 1 Press the upper side of the faceplate. The faceplate will open. 2 Push the bottom of the control panel and close the faceplate. NOTE The buttons do not work when the control panel is slided. 2 CAUTION Do not set the right side of the faceplate in the faceplate bracket first, when reattaching the faceplate. Doing so may cause the connector on the faceplate bracket to malfunction. — 7— English General features Loudness This function amplifies turned down. The LOUD indicator lights on. Turning Loudness On/Off: Hold down the LOUD button for the loudness on and off. Audio Control Setting Adjust various parameters of sound quality. 1 Press the AUD button to enter the control mode. 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, the adjustment mode will change. Please refer to the following for the contents of the adjustment modes. NOTE Source tone memory Each source (tape, FM, AM, and disc changer) has its own memory in which to store the bass and treble tone settings. The settings made for a particular source are then recalled automatically whenever you use that source (e.g., FM mode uses the tone settings made for FM, AM for AM, etc.). 3 Adjust each mode Press the 4/ . button. Please refer to the following for the adjusting values. 4 Press the AUD button to end the control mode. "dB/DB" : Recalling the kenwood preset sound setting Press the preset buttons Settings: #1;Flat, #2;Rock, #3;Pops/#6;Scan of #1-5 NOTE • This mode is available only when is on. (page 29) • You can call the following settings centre frequency, bass level, bass quality extension, treble centre frequency, and Their setting values are different depending the mobile preset plan mode. “Bass/BAS” : Adjust the bass level. Setting values: - 8 – + 8 “Treble/TRE” : Adjust the treble level. Setting values: - 8 – + 8 “Balance/BAL” : Adjust the balance level. Setting values: Left 15 – Right 15 “Fader/FAD” : Adjust the fader level. Setting values: Front 15 – Rear 15 — 8— Tuner features "V OFFSET/VOS" : Set the sound level of the each source selected by adjusting the level difference FM SRC . between the basic sound level and the required level. Setting values: - 8 – ± 0 Mobile Preset This function allows you to adjust the setting with the sound coordinate system, according DISP AM speakers. 1 Press the SRC button repeatedly to select the standby KRC-678R/678RV "ALL OFF" is displayed when the standby mode is selected. Preset station number 2 Press the AUD button to enter the mobile preset plan mode. 3 Press either the 4 or . button to select the type of speaker. The setting switches as follows. Off / For the OEM speaker / For 6/6x9 in. speaker / For 5/4 in. speaker 4 Press the AUD button to end the mobile preset plan mode. DISC PROG/PTY DAB EJECT #1-6 AUDAUD FrequencyBand display ST indicator NOTE • This mode is available only when the Sound coordinate system AUTO indicator is on. (page 29) • When you change the setting of type of speaker, the bass and KRC-578R treble tone settings are returned to original levels. Band display Preset station number Frequency ST indicator AUTO indicator — 9— Tuner features English Tuning 1 Press the SRC button obtained. "TUNER" is displayed selected. 2 Press either the FM or AM button Each time you press the FM button, between the FM1, FM2 and FM3. Press the AM button to select the MW 3 • Auto Seek Tuning Press the . button to seek increasing frequencies. Press the 4 button to seek decreasing frequencies. • Preset station seek tuning Press the . button to move to the next preset station (i.e., the one with the next highest number), and the 4 button to move to the last preset station (i.e., the one with the lowest number). NOTE If the frequencies stored at the preset numbers receive stations which were not originally memorized when traveling long distances, the preset number is not displayed. In such cases, pressing the 4/ . button to use preset station seek will receive channel 1. • Manual Tuning Press the . button to increase the frequency by one step. Press the 4 button to decrease the frequency by one step. NOTE • The ST indicator lights up when stereo broadcasts are being received. • Please see the menu settings about selecting tuning mode. (page 30) 1 Select the band/ 2 Hold down the button station, for two seconds The button number blinks the data has been stored. Recalling a Preset Station: Press the preset station button (#The number of the recalled station NOTE You can store 6 stations in each of the FM1, (MW and LW) bands. Switching Display for Tuner You can change the display used when listening to the Switching the Display: Pressing the DISP button switch...
Este manual também é adequado para os modelos :Unidade - KRC-578R (580.53 kb)
Unidade - KRC-678R (580.53 kb)