Assessments - 3, GPA: 3.3
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
• If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits do not remove the caps from unused terminals or from the ends of the unconnected cables. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected wires with vinyl tape or other similar material. •Mount the unit so that the mounting angle is 30° or less. 2 CAUTION Installation Accessories Installation Procedure ........1 1 ........1 2 External view ......... Number of items ........1 3 ........2 4 CAR DIVERSITY ANTENNA WITH BOOSTER CX-A330 ON OFF BOOST ........2 6 ........1 7 ........6 8 ........1 5 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2 CAUTION ........1 9 ........2 0 Installation of Monior Unit When mounting the main unit after checking the operation, close the monitor first. • Move the fittings on both sides to suit the installation chassis and select the embedding position from among the 3 positions.( :Fixing screw) •When the fittings are set closest to the front (i.e., the embedding position is farthest back), use the hard rubber frame (Accessory 5). NOTE 2 CAUTION Accessory 5 Accessory 9 English UPUPOn cars where there is no compartment in the centre for installing a car audio unit: Use the spacer (Accessory 0) to affix the centre unit sleeve and the sleeve attached to the main unit in such a way that they are correctly aligned both depthwise and horizontally. On cars lacking a centre compartment Accessory 0 Removing Unit ¦ Removing the Hard Rubber Frame 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. CatchLock Accessory 4 n Removing the Unit 1 Refer to the section “Removing the Hard Rubber Frame” and then remove the hard rubber frame. 2 Remove the Hex-head screw (Accessory 9) with integral washer (M4. 8) on the back panel. Catch facing up 3 Insert the two removal tools deeply into the slots on each side, as shown. 2 CAUTION Be careful to avoid injury from the catch pins on the removal tool. 4 Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 2 When the lower level is removed, remove the upper two locations. NOTE The frame can be removed from the top side in the same manner. 5 Pull the unit all the way out with your hands, being careful not to drop it. 31 Installation English Connections Accessory 6 M 4 IN OUT NAV I / F ILLUMI ACC PRK SW BATT – + CAR DIVERSITY ANTENNAWITH BOOSTER CX-A330ONOFFBOOST CAR DIVERSITY ANTENNAWITH BOOSTER CX-A330ONOFFBOOST MASTER SW Battery cable (Yellow) »12V Ignition cable (Red) »12V Fuse (5A) Automatic illumination control cable (Orange) Parking sensor cable (Green) To parking brake detection switch harness of car For the sake of safety, be sure to connect the parking sensor. 2 CAUTION To car headlight switch Ignition key switch Car fuse box(Main fuse) ACC Ground cable (Black) a (To car chassis) Battery Audio/Visual Input or Output •Visual (Yellow) •Audio left (White) •Audio right (Red) When disconnecting the I/F cable, pull on the connector’s ring. 2CAUTION Kenwood navigation unit KTC-1000R/A907 C907 When the KTC-1000R is connected, NOTE KVC-1000 Accessory 3 Accessory 1 Accessory 2 IN-OUT setting •Set to "IN" when using a video player or when connecting a navigation unit other than Kenwood. •Set to "OUT" when connecting to another monitor. NOTE Connection cable (Provided with the C907) Connection cable (Provided with the KTC-1000R/A907) MASTER SW cable (White/Red) When not connected to the KTC-1000R/A907, this cable should be connected to a. 32 2 CAUTION see the KTC-1000R Instruction Manual The unit will not operate unless the cable is connected. Connecting and Install Antenna Units n Connection of Antenna Unit 2 CAUTION Incar antennas have a lower reception sensitivity than antennas intended for outside mounting. The picture may not appear or may be disturbed if the signal in your area is weak. English CAR DIVERSITY ANTENNAWITH BOOSTER CX-A330ONOFFBOOST – + Booster switch Set this booster switch to "OFF" if there is ghosting of the on-screen image due to electromagnetic fields. ON OFF To the monitor unit Ignition cable (Red)»12V Ignition key switch Car fuse box (Main fuse) ACC Ground cable (Black) a (To car chassis) Battery Fuse(1A) n Installation forAntenna Unit • Attach the antenna to the inner glass surface of the rear window using double-sided tape. Carefully check the installation location as the tape can only be stuck on once. • If the surface temperature of the glass of the rear window is low, warm it by turning on the power of...