Assessments - 3, GPA: 4 ( )

Fabricante : Kenwood Arquivo Tamanho: 429.49 kb Arquivo Nome : Língua de Ensino:

— 4— About CDs About CDs • Don’t touch the recording • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD. Also, don’t use a CD with tape stuck on it. When using a new CD If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc. Burrs Burrs CD accessories Don’t use disc type accessories. CD cleaning Clean from the center outward. Removing CDs When removing CDs from this unit pull them out horizontally. CDs that can’t be used • CDs that aren’t round can’t be used. • CDs with coloring on the recording surface or that are dirty can’t be used. • This unit can only play the CDs with . It may not correctly play discs which do not have the mark. • A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.) — 5— CD storage • Don’t place them in direct seat or dashboard etc.) temperature is high. • Store CDs in their cases. General General English Release button (KDC-4023/KDC-3023/KDC- AM FM . 4ud SRC ATT/ #1 #3 CLK/ Q/ LOUD ADJ AUD KDC-4023/KDC-3023/KDC-2023 ATT indicator LOUD indicator SYSTEM Q indicator ATT indicator LOUD indicator SYSTEM Q indicator KDC-1023/KDC-1023S Clock indicator Clock display Clock indicator Clock display Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at Selecting the Source Press the [SRC] button. Source required Display Tuner "TUnE" CD "CD" External disc "DISC" (Function of the KDC-4023/KDC-3023/KDC-2023) Standby (Illumination only mode) "OFF" Volume Increasing Volume Press the [ u] button. Decreasing Volume Press the [ d] button. Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. Loudness Compensating for low and high tones during low volume. Press the [LOUD] button for at least 1 second. — 6— Each time the button Each time the button 4 Adjust the Audio When it’s ON, "LOUD" indicator Press the [ 4] or [ . ] button. System Q Adjustment Item Display Range Bass level "BAS" –8 — +8 You can recall the best sound the music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed the sound setting Sound setting Display Middle level "MID" –8 — +8 Treble level "TRE" –8 — +8 Balance "BL" Left 15 — Right 15 Fader "FD" Rear 15 — Front 15 5 Exit Audio Control mode Press the [AUD] button. Speaker Setting Flat "SQ-1" Fine-tuning so that the System Q value is optimal when Rock "SQ-2" the speaker type. Top 40 "SQ-3" 1 Enter Standby Pops "SQ-4" Press the [SRC] button. Jazz "SQ-5" Select the "OFF" display. Easy "SQ-6" 2 Enter Speaker Setting mode • Each setting value is changed with the (page 7). First, select the speaker type with the Speaker setting. Press the [Q] button. • When the System Q setting is changed, the Bass, Middle, and 3 Select the Speaker type Treble set in audio control replace the System Q values. Press the [ 4] or [ . ] button. Audio Control Each time the button is pressed the setting switches as shown below. 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted Speaker type Display OFF "SP-F" For the OEM speaker "SP-O" For 6 & 6x9 in. speaker "SP-6" For 5 & 4 in. speaker "SP-5" 4 Exit Speaker Setting mode Press the [Q] button. — 7— General General Clock Display Press the [CLK] button. Each time the button is OFF. When it’s ON, the clock indicator is ON. Adjusting Clock 1 Select the clock display Press the [CLK] button. 2 Enter clock adjustment mode Press the [CLK] button for at least 2 seconds. The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] button. Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit clock adjustment mode Press the [CLK] button. Function of the KDC-4023/KDC-3023/KDC-2023 DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. 1 Turn the power OFF Press the [SRC] button for at least 1 second. 2 Set the DSI While pressing the [#1] and [#3] button, press the [SRC] button. Each time the step 1 and 2 operation is done the DSI turns ON or OFF. Function of the KDC- Theft Deterrent Faceplate The faceplate of the unit can helping to deter theft. Removing the Faceplate Press the Release button. The faceplate is unlocked, allowing you to • The faceplate is a precision piece of equipment and damaged by shocks or jolts. For that reason, keep the faceplate its special storage case while detached. • Do not expose the faceplate or its storage case to ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :