• Mount the unit so that the mounting angle is 30° or less. English | 15 ANT. CONT MUTE P.CONT FRONT • L FRONT • R REAR • L REAR • R – + Connecting Wires to Terminals FM/AM antenna input Rear left output (White) Rear right output (Red) Fuse (10A) Wiring harness (Accessory1) Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) ACC Car fuse box If no connections are made, do not let the wire come out from the tab. When using the optional power amplifier, connect to its power control terminal. Power control wire (Blue/White) Motor antenna control wire (Blue) Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. To front left speaker To front right speaker To rear left speaker To rear right speaker White/Black White Gray/Black Gray Green/Black Green Purple/Black Purple Ignition key switch Car fuse box (Main fuse) Battery Connect to the terminal that is grounded TEL mute wire (Brown) when either the telephone rings or during conversation. 16 | English Installation • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). non-Japanese cars Japanese cars 1 Refer to the section (page 18) and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Metal mounting strap (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 8 mm MAX. o5mm o5mm 8mm MAX. T N T N T/N T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car 3 4 English | 17 Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screws in the holes shown below. Accessory5 • Never insert the screw in any other screw hole than the one specified. If you screw them in another hole, it will contact and may cause damage to the mechanical parts inside the unit. 18 | English Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. 2 When the upper level is removed, remove the lower two locations. • The frame can be removed from the bottom side in the same manner. Removing the Unit 1 Refer to the section (page 18) and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. Catch Lock Accessory2 Removal tool Accessory2 Removal tool Screw (M4X8) (commercially available) English | 19 Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. . Wire or insulate the speaker cable properly and press the reset button. ? There’s a source you can’t switch. . There’s no media inserted. . Set the media you want to listen to. If there’s no media in this unit, you can’t switch to each source. ? The memory is erased when the ignition is turned OFF. . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? The TEL mute function does not work. . The TEL mute wire is not connected properly. . Connect the wire correctly, referring to the section on . ? The TEL mute function turns ON even though the TEL mute wire is not connected. . The TEL mute wire is touching a metal part of the car. . Pull the TEL mute wire away from the metal part of the car. ? Even if Loudness is turned ON, high-pitched tone isn’t compensated for. . Tuner source is selected. . High-pitched tone isn’t compensated for when in Tuner so...
)
