Assessments - 2, GPA: 3
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
(Original setting) "OFF 40M" Turns the power OFF after 40 minutes. "OFF 60M" Turns the power OFF after 60 minutes. — 21 — English English External view Number of items .......................................... 1 1 .......................................... 2 2 .......................................... 1 3 The use of any accessories except for those provided might damage to the unit. Make sure only to use the accessories the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the reset button. 2CAUTION • If your car is not prepared consult your Kenwood • Only use antenna conversion antenna cord has an ISO • Make sure that all wire connections inserting jacks until they lock • If your vehicle's ignition does not ignition wire is connected to a power voltage such as a battery wire, the power the ignition (i.e., it will not turn on and off ignition). If you want to link the unit's power connect the ignition wire to a power source on and off with the ignition key. • If the fuse blows, first make sure that the wires a short circuit, then replace the old fuse with one with rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. — 22 — Connecting Connecting Rear right output (Red) Antenna Conversion Adaptor REARLR (ISO–JASO) (Accessory3) To connect the Disc changer, consult your Disc changer manual. KENWOOD disc changer input (KDC- Antenna Cord (ISO) Fuse (10A) Connector Function Guide Pin Numbers for ISO Connectors Wire Color Functions External Power Connector A–4 A–5 A–7 A–8 Yellow Blue/White Red Black Battery Power Control Ignition (ACC) Earth (Ground) Connection Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) — 23 — 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 TEL MUTE P.CONT ANT.CONT Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B See page 24 Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. English English 2WARNING Connecting the ISO (see p.23) The pin arrangement vehicle you drive. Make prevent damage to the unit. The default connection for the 1 below. If the ISO connector pins are set 2 or 3, make the connection as illustrated. Please be sure to reconnect the 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle's is linked with the ignition, and the A-4 pin (yellow) the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) When the connection is made as in 3 above, the unit's power will not be linked to the ignition key. For that reason, always make sure to turn off the unit's power when the i...
Este manual também é adequado para os modelos :Unidade - KDC-307 (545.83 kb)
Unidade - KDC-4024 (545.83 kb)
Unidade - KDC-4024V (545.83 kb)