Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
• Mount the unit so that is level. tion. • Changer unit is mounted in an • Mount the unit in a stable place. unstable place. • The angle adjustment switches • Set the angle adjustment are set improperly. switches to the correct positions. The disc changer mode The O-N selection switch of the Set the O-N selection switch to cannot be selected. disc changer is not set properly. "O" position. When removing the CD changer, be sure to first eject a magazine then unplug the changer cord. Do not forget to attach the transport screws before transporting the CD changer. The CD changer may be damaged during transport if a magazine or CD is left inside it or the transport screws are not attached. Specifications Specifications subject to change without notice. Laser diode ..................................................................................................GaAlAs ( .=780 nm) Digital Filter..............................................................................................8 Time Over Sampling D/A Converter.................................................................................................................. .....1 bit Spindle speed.............................................................................................500 ~ 200 rpm (CLV) Wow & Flutter......................................................................................Below Measurable Limit Frequency Response (±1 dB) ...............................................................................5 Hz ~ 20 kHz Total harmonic distortion (1 kHz) ...................................................................................0.005 % Signal to Noise Ratio........................................................................................................100 dB Dynamic range .................................................................................................................. .94 dB Channel separation............................................................................................................. 96 dB Operating voltage...........................................................................14.4 V (11 ~ 16 Current consumption ................................................................................0.8 A at Rated Dimensions (W . H . D) (KDC-C717) ........................................250 . 80 . 176 mm (9-13/16 . 3-1/8 . 6-13/16 in. ) (KDC-C667) ........................................250 . 64 . 176 mm (9-13/16 . 2-1/2 . 6-13/16 in. ) Weight (KDC-C717) ............................................................................................(KDC-C667) ............................................................................................ COMPACT DISC AUTO CHANGER KDC-C717 KDC-C667 INSTRUCTION MANUAL ©B64-1801-20 Warning / Safety precautions The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is using laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. 2WARNING Take the following precautions to prevent fire and avoid personal injury : • Check that no metal objects (coins, tools, etc.) are left inside the unit to avoid short circuits. • If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. 2CAUTION Take the following precautions to keep the unit in proper working order. • Do not open the top or bottom cover. • Do not install the unit in places it is exposed to direct sunlight, high heat or humidity, water may splash over it, or dust exists. • Do not install the unit at a dusty place. If the unit is installed at a dusty place, dust accumulates inside the unit and unit may be damaged. • When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. on the other side. • If the unit is installed near speakers, the speakers vibration may causes a sound skip. Install the unit as far away as possible from the speakers. NOTE • If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer. • If it doesn't seem to be working properly, first press the Reset button. If the malfunction persists, consult your Kenwood dealer. IMPORTANT INFORMATION • This unit is NOT designed to be connected to control units that are manufactured and before 1994. If used with such units, CA-SD200 (sold separately) must be FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT CONTROL UNIT. • The disc name preset function of up to 100 discs using each disc name. The availability of of discs which and the variable Do Not Use Special Shape CDs • Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction. • Be sure to use CDs with disc mark only for this unit. • C...
Este manual também é adequado para os modelos :Unidade - KDC-C667 (249.33 kb)