Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
To cancel the forced closing of unit and open control panel: Press the left part at the upper side of the faceplate. The faceplate will open and show the control panel. The faceplate can theft. Removing the faceplate: 1 Choose the way from among faceplate. Turn the ignition off, hold down the or more when the control panel has 2 Holding the centre part of the faceplate, period which you have set in the "Time setting the faceplate" (page 38) in the menu. The faceplate bracket will automatically close. 2 CAUTION • When removing the faceplate, pull it out only when it is fully open. The detachment of the faceplate whilst it is moving might result in damage to the unit. • Do not apply excessive force to the faceplate bracket without attaching the faceplate. Doing so will cause the faceplate bracket to be deformed. • Do not touch the connector on the faceplate bracket after removing the faceplate. Touching the connector may cause damage to the unit. NOTE • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case whilst detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. — 14 — Reattaching the Faceplate: 1 Hold the faceplate toward you and set faceplate bracket. 1 Hold the faceplate toward you and set faceplate bracket. 2 CAUTION Do not set the right side of the first, when reattaching the faceplate. connector on the faceplate bracket 2 Press the right side of the faceplate until Function of the KDC-PS9590R/KDC-9090R Non-Fading Output You can turn the non-preout is switched to the Turning non-fading output On/Off : Hold down the NF button for one function ON or OFF. "NF ON" is displayed when the non- TEL Mute Shut down the audio system temporarily whenever an incoming call is received. NOTE The function will not work if a cable is not connected to the car phone. When the telephone rings: When a call is received, "CALL" is displayed and all the unit functions are temporarily interrupted. Restoring Original Unit Source During Phone Call: Press the SRC button. "CALL" disappears from the display, and the volume of the original source is restored gradually. Turning TEL Mute Function Off After Phone Call: Hang the phone up. "CALL" disappears from the display. The original source (i.e., the one used before the phone call) is returned to automatically, and the volume restored gradually. — 15 — Audio control features Audio Control Adjust various parameters FM English PTY LOUD OFF AUD VOL ADJ MENU ANG NAME DISP AMAUD 4 KDC-PS9590R/9090R Selecting mode Setting value 1 Hold down the AUD button the control mode. 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, the change. Please refer to the following for the contents adjustment modes. NOTE Source tone memory Each source (CD, MD, FM, AM, and disc changer) memory in which to store the bass, middle, treble settings. (N-F level : KDC-PS9590R/9090R only) The settings made for a particular source are then recalled automatically whenever you use that source (e.g., FM mode uses the tone settings made for FM, AM for AM, etc.). 3 Adjust each mode Press the 4/ . button. Look at the table to adjust the mode being displayed. 4 Press the AUD button to end the control mode. NOTE KDC-8090R Selecting mode Setting value • Determining the parameters in the audio control setting will clear all the adjustments made in the System Q and they are replaced with the values made in the audio control setting. • The following parameters can be set when the System Q function on the menu settings is ON. Bass centre frequency, bass quality factor, bass extend, middle centre frequency, middle quality factor, and treble centre frequency. — 16 — Bass Centre Middle Centre Adjust the centre Display and setting: "Bass FRQ" : 60 / 70 / 80 factor is set to 1.00, 1.25 or when the bass quality factor is Bass Level Adjust the bass level. Display and setting: "Bass" : - 8 – + 8 Adjust the centre Display and setting: "MID FRQ" : 0.5 / 1.0 / 1.5 / 2.0 kHz. Middle Level Adjust the middle level. Display and setting: "MID" : - 8 – + 8 Middle Quality Factor Adjust the middle quality factor. Bass Quality Factor Adjust the Bass quality factor. Display and setting: "Bass Q" : 1.00 / 1.25 / 1.50 / 2.00 Bass Extend Switch the Bass Extend mode on/off. Display and setting: "Bass EXT" : ON / OFF (When the bass extend mode is set to on, low frequency response is extended by 20%.) Display and setting: "Middle Q" : 1.0 / 2.0 Treble Centre Frequency Adjust the centre frequency of the treble. Display and setting: "TRE FRQ" : 10.0 / 12.5 / 15.0 / 17.5 kHz Treble Level Adjust the treble level. Display and setting: "TRE" : - 8 – + 8 — 17 — Audio control features Balance Level NOTE You can separately output, including preouts. Adjust the balance Display and setting: non-fading preou...
Este manual também é adequado para os modelos :Unidade - KDC-8090R (609.05 kb)
Unidade - KDC-9090R (609.05 kb)