Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Changing setting for currently displayed function Press either the 4or .button. The setting will change for each function. Example: The setting of the touch sensor tone will switch from on to off, and "Beep OFF" is displayed. Ending the menu mode Press the MENU button. Make sure to end the menu mode when finished. NOTE 4 3 2 1 Menu System Menu settings — 28 — English AM 4 . SRC MENU FM DISP #1-6 KDC-7018/KDC-5018 KDC-V7018R Menu display Menu display AUTO indicator NEWS indicator RDS indicator beofonrOce ntd chtihesepea tos phpsepersceo iusbacrerleiestcdy utfu orcroi oetcmyd ai sec nt o chfideueneln i sM tcfhtuEiesonNd ncf,Utu ciont a sncnyt e hsiboetaeneds m tanbuf.oetr enNte rebnowde tae a ocretntdhip.vs aea.Ht at oeitwed wd,e ."iv Slenrco, u lroitnyg" er be before the security code function can be turned on. However, once the procedure is finished, it need not be repeated. Once the security code function has been activated, "Security" disappears from the MENU system. Note that it will no longer be possible to cancel this function afterwards. 4 5 6 7 Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected. Press the MENU button for at least one second. "MENU" is displayed first and then "Security" is displayed. Press either the 4 or . button for at least two seconds. "ENTER" will appear in the display for one second, indicating the code setting mode has been entered. When "CODE" appears in the display, you can start inputting the code. Press the preset button and enter your security code. Use the security code shown on your Car Audio Passport. Example: Enter "3510" as your code, pressing the buttons as follows: Step Button to press # Times pressed Display 1 #1 4 “3” 2 #2 6 “5” 3 #3 2 “1” 4 #4 1 “0” Press the DISP button for at least three The security code will be set. "RE-ENTER" will appear in the display you to enter the code once again "CODE" appears in the display, code. Press the Preset button Press the DISP button "APPROVED" will function turning disconnected entered the "ENTER" and "CODE" will appear in the display, asking you to input the code. NOTE If you input an incorrect security code, the code setting mode will be canceled automatically. Follow the steps from 3 to 7 above again. If you press the RESET button or remove the battery: The first time you turn the unit on again, "CODE" will appear in the display, asking you to input the security code. Repeat steps 6 and 7 above, and input the security code. You can start operating the unit again when "APPROVED" appears in the display. NOTE If you enter the wrong code, "Waiting" is displayed and you cannot make further input of the code for a fixed interval (see table below), which grows longer each time you enter the wrong code. When "CODE" is displayed, you can make input again. Number of wrong Interval until next input inputs is allowed 1 -2 5 minutes 3 1 hour 4 24 hours The number of wrong inputs is displayed. Touch Sensor Tone This function produces a beep operation. It can be switched Display and setting: "Beep ON" : Beep setting is on. "Beep OFF" : Beep setting is off. NOTE The beep — 29 — English English Manual Time Adjustment NOTE Adjust the time manually. NOTE (KDC-V7018R only) This adjustment is available only when the automatic time adjustment is set to off. (page 30) Display and setting: 1 Select the display "Clock Adjust" during the selecting function in the menu system. 2 Press either the 4 or . button for at least one second to enter the Manual time adjustment mode. The time display will blink. 3 • Adjusting the hours Press the FM button to advance the hours, or press the AM button to make the hours go back. • Adjusting the minutes Press the . button to advance the minutes, or press the 4 button to make the minutes go back. 4 Press the MENU button to end the Manual Time Adjustment mode. Exiting the Manual Time Adjustment mode would start the clock counting. Function of the KDC-V7018R Automatic Time Adjustment With automatic time adjustment, you automatically according to time data (after receiving RDS signals for set the time manually if the automatic function is turned off. Display and setting: "SYNC ON" : Automatic "SYNC OFF" : Manual Adjusting Time Tune into an The time adjusts The time is not adjusted when the RDS station you are tuned to is not transmitting a time signal. Choose another RDS station in such a case. Function of the KDC-7018/KDC-V7018R Selectable Illumination You can switch the color of the button illumination between green and red. Display and setting: "Button Green" : The color of the illumination is green. "Button Red" : The color of the illumination is red. Switching Graphic Display This function allows you to turn off the lower part of the display if there is too much information in the display. Display and setting: "Graphic ON" : The display will turn on by using the whole of the display. (Default setting) "Graphic OFF" : The display will turn on by ...
Este manual também é adequado para os modelos :Unidade - KDC-5018 (772.91 kb)
Unidade - KDC-7018 (772.91 kb)