Log:
Assessments - 2, GPA: 4 ( )

Instruções de Operação Kenwood, Modelo KDC-W241

Fabricante : Kenwood
Arquivo Tamanho: 580.5 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



por este dispositivo também tem outras instruções :
Unidade - KDC-W241 (589.74 kb)ru
Unidade - KDC-W241 (583.67 kb)ru
Unidade - KDC-W241 (590.78 kb)en

Facilidade de uso


Ignition cable (Red) A-7 Pin (Red) Unit Vehicle A-4 Pin (Yellow) Battery cable (Yellow) . • When the connection is made as in 3 above, the unit’s power will not be linked to the ignition key. For that reason, always make sure to turn off the unit’s power when the ignition is turned off. To link the unit’s power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. 16 | KDC-W3041/KDC-W312/KDC-W241/KDC-241 Installation/Removing the Unit Installation Removing the hard rubber frame Metal mounting strap (commercially available) Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Catch Lock Accessory2 Removal tool 2 When the upper level is removed, remove the lower two locations. . • The frame can be removed from the bottom side in the same manner. . • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Removing the Unit 1 Refer to the section and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Screw (M4X8) (commercially available) Accessory2 ¤ • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. English | 17 Troubleshooting Guide Some functions of this unit may be disabled by The messages shown below display your some settings made on this unit. systems condition. ! TOC ERR: • No disc has been loaded in the disc Cannot display the user of System Q. magazine. ^

recorded that the unit can play. (page 10) • (page 4) is not set to On. E-77: The unit is malfunctioning for some reason. . Press the reset button on the unit. If the “E! 77” code does not disappear, consult your Cannot set up Display. ^ (page 11) is not nearest service center. turned off. E-99: Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. . Check the disc magazine. And then press What might seem to be a malfunction in your unit the reset button on the unit. If the “E-99” code does not disappear, consult your may just be the result of slight misoperation or nearest service center. miswiring. Before calling service, first check the following table for possible problems. IN (Blink): The CD player section is not operating properly. Tuner source . Reinsert the CD. If the CD cannot be ejected or the display continues to flash ? Radio reception is poor. even when the CD has been properly . The car antenna is not extended. reinserted, please switch off the power . Pull the antenna out all the way. and consult your nearest service center. Disc source PROTECT: The speaker wire has a short-circuit or touches the chassis of the vehicle, and then The specified disc does not play, but another one the protection function is activated. ? plays instead. . Wire or insulate the speaker cable . The specified CD is quite dirty. properly and press the reset button. If . Clean the CD. the “PROTECT” code does not disappear, . The disc is loaded in a different slot from that consult your nearest service center. specified. . Eject the disc magazine and check the number NA FILE: An Audio file is played with a format that this for the specified disc. unit can’t support. . The disc is severely scratched. . --- . Try another disc instead. COPY PRO: A copy-protected file is played. . --- Audio file source ? The sound skips when an Audio file is being played. . The media is scratched or dirty. . Clean the media, referring to the CD cleaning of the section on (page 3). . The recording condition is bad. . Record the media again or use another media. 18 | KDC-W3041/KDC-W312/KDC-W241/KDC-241 Specifi cations FM tuner section Frequency range (50 kHz space) : 87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 26dB) : 0.7 .V/75 . Quieting Sensitivity (S/N = 46dB) : 1.6 .V/75 . Frequency response (±3.0 dB) : 30 Hz – 15 kHz Signal to Noise ratio (MONO) : 65 dB Selectivity (DIN) (±400 kHz) : . 80 dB Stereo separation (1 kHz) : 35 dB MW tuner section Frequency range (9...

Este manual também é adequado para os modelos :
Unidade - KDC-241 (580.5 kb)
Unidade - KDC-W3041 (580.5 kb)
Unidade - KDC-W312 (580.5 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias