. • If you enter a Code different from your Security Code, you have to start over from step 4. Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed 1 Turn the power ON. 2 Do the step 4 through 7 step operation, and reenter the security code. "APPROVED" is displayed. Now, you can use the unit. . • If an incorrect code is entered, "WAITING" is displayed, and the input prohibition periods shown in the table below is generated. After the input prohibition time lapses, "CODE" is displayed, and you can reenter the code. Number of times the incorrect code was input Input prohibited time 1— 2 5 minutes 3 1 hour 4 24 hours In Standby mode Touch Sensor Tone Setting the operation check sound (beep sound) ON/OFF. Display Setting "BEEP ON" Beep is heard. "BEEP OFF" Beep canceled. In Standby mode Manual Clock Adjustment . • You can do this adjustment when the (page 22) is set as OFF. 1 Select Clock Adjustment mode Push the Control knob towards [FM] or [AM]. Select the "CLK ADJ" display. 2 Enter Clock Adjust mode Press the Control knob for at least 1 second. The clock display blinks. 3 Adjust the hours Push the Control knob towards [FM] or [AM]. Adjust the minutes Push the Control knob towards [4] or [.]. 4 Exit Clock adjustment mode Press the [MENU] button. English | 21 Menu system Function of KDC-W4037/KDC-W3537/ KDC-W3037/KDC-W311 In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit’s clock. Display "SYNC ON" "SYNC OFF" Setting Synchronizes the time. Adjust the time manually. . • It takes 3 to 4 minutes to synchronize the clock. In Standby mode DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF. Function of KDC-W4037 In Standby mode Selectable Illumination Selecting the button illumination color as green or red. Display Setting "KEY RED" The illumination color is red. "KEY GRN" The illumination color is green. Dimmer You can lower the brightness of the display by using the dimmer function. Display Setting "DIM ON" The display dims. "DIM OFF" The display doesn’t dim. Function of KDC-W4037 In Standby mode Switching preout Alternating the preout between the rear and subwoofer. (With the subwoofer the sound outputs without being effected by fader control.) Display Setting "SWPRE R" Rear preout. "SWPRE SW" Subwoofer preout. In Audio file source Supreme Setting When MP3 or WMA files encoded at a low bit rate (less than 96kbps (fs=32k, 44.1k, 48kHz)) are played, this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate. Processing is optimized for the compression format used (MP3, or WMA), and adjustment is made for the bit rate used. Display Setting "SPRM ON" Plays sound using the Supreme function. "SPRM OFF" Plays the original sound stored in the audio file. . • The sound effect may be imperceptible depending on the relationship between the audio file format and setting. Function of KDC-W4037/KDC-W3537/ KDC-W3037/KDC-W311 News Bulletin with Timeout Setting The tuner automatically changes when a news bulletin starts even if the radio is not being listened to. Also, you can set the time interval when interruption is prohibited. Display and Setting "NEWS OFF" "NEWS 00M" "NEWS 90M" … 22 | English When you set "NEWS 00M" — "NEWS 90M", the News Bulletin Interrupt function is ON. When the News Bulletin is ON, the "NEWS" indicator is ON. When the news bulletin starts, "NEWS" is displayed, and the tuner changes to the news bulletin. . • If you choose the "20MIN" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. • The news bulletin volume is the same level that was set for (page 13). • This news bulletin function is only available if the desired station sends PTY-code for news bulletin or belongs to -Network sending PTY-code for news bulletin. • When the News Bulletin Interrupt function is ON, the tuner changes to an FM station. In Tuner mode Local Seek Only stations whose reception is good are searched in auto seek tuning. Display Setting "LO.S OFF" The local seek function is OFF. "LO.S ON" The local seek function is ON. Function of KDC-W4037/KDC-W3537/ KDC-W3037/KDC-W311 In Tuner mode Tuning Mode Sets the tuning mode. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. Preset station seek "AUTO 2" Search in order of the stations in the Preset memory. Manual "MANUAL" Normal manual tuning control. Function of KDC-W4037/KDC-W3537/ KDC-W3037/KDC-W311 AF (Alternative Frequency) When the reception is poor, automatically alternate to another frequency broadcasting the same program in the same RDS network with better reception. Display Setting "AF ON"...
)
