In Standby mode Manual Clock Adjustment • This adjustment can be done when the (page 36) is set as OFF. 1 Select Clock Adjustment mode Push the Control knob to [FM] or [AM]. Select the "Clock Adjust" display. 2 Enter Clock Adjust mode Press the Control knob for at least 1 second. The clock display blinks. 3 Adjust the hours Push the Control knob to [FM] or [AM]. Adjust the minutes Push the Control knob to [4] or [.]. 4 Exit Clock adjustment mode Press the [MENU] button. 36 | English Menu system In Standby mode Date Adjustment 1 Select Date Adjust mode Push the knob to [FM] or [AM]. Select the "Date Adjust" display. 2 Enter Date Adjust mode Press the Control knob for at least 1 second. The date display blinks. 3 Selecting the item (day, month, or year) to adjust Push the Control knob to [4] or [.]. The items that are blinking are items that can be adjusted. 4 Adjust each item Push the Control knob to [FM] or [AM]. 5 Repeat step 3 and 4 operation and adjust the date. 6 Exit Date adjustment mode Press the [MENU] button. In Standby mode Date Mode Setting the date format. 1 Select Date Mode Push the Control knob to [FM] or [AM]. Select the "Date Mode" display. 2 Select the date format Push the Control knob to [4] or [.]. 3 Exit Menu mode Press the [MENU] button. In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit’s clock. Display Setting "SYNC : ON" Synchronizes the time. "SYNC : OFF" Adjust the time manually. • It takes 3 to 4 minutes to synchronize the clock. In Standby mode DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI : ON" LED flashes. "DSI : OFF" LED OFF. In Standby mode Selectable Illumination Selecting the button illumination color as green or red. Display Setting "Button : Red" The illumination color is red. "Button : Green" The illumination color is green. In Standby mode Dimmer Dimming this unit’s display automatically when the vehicle light switch is turned ON. Display Setting "Dimmer : ON" The display dims. "Dimmer : OFF" The display doesn’t dim. Function of the KDC-W7031 In Standby mode Switching preout Switching the preout between the rear and subwoofer. (In subwoofer it outputs without effect from the fader control.) Display Setting "SWPRE : Rear" Rear preout. "SWPRE : Sub-W" Subwoofer preout. English | 37 In Standby mode Built-in Amp Setting Built-in amplifier is controlled. Turning OFF this control enhances the preout quality. Display Setting "AMP : ON" The built-in amplifier activates. "AMP : OFF" The built-in amplifier deactivates. Function of the KDC-W7031 In Standby mode G-Counter Level set Calibrating G-Counter. Setting the level according to the kinds of vehicles. Display Setting "G-Counter: Level1" Counter is easy to go up. "G-Counter: Level2" … "G-Counter: Level3" Counter is hard to go up. • In the case of less acceleration, set it up to "G-Counter: Level1". In the case of frequent acceleration, set it up to "G-Counter: Level3". Function of the KDC-W7031 In Standby mode G-Analyzer Reset Resets the value of G-Meter and G-Counter. 1 Select G-Analyzer Reset mode Push the Control knob to [FM] or [AM]. Select the "G-Reset" display. 2 Enter G-Analyzer Reset mode Press the Control knob for at least 1 second. 3 Select the Reset item Push the Control knob to [FM] or [AM]. "G-Meter Reset": Reset the value of G-Meter. "G-Counter Reset": Reset the value of G-Counter. 4 Reset the value Press the Control knob for at least 2 seconds. "Reset OK" is displayed. 5 Exit G-Analyzer Reset mode Press the [MENU] button. Function of the KDC-W7031 In Standby mode G-Analyzer Calibration setup G-Analyzer requires calibration for horizontal acceleration and braking. • Detection of horizontal and straight directions should be done at horizontal location to go straight. 1 Park the vehicle at horizontal location 2 Select G-Analyzer Calibration set mode Push the Control knob to [FM] or [AM]. Select the "G-Calibration" display. 3 Enter G-Analyzer Calibration set mode Press the Control knob for at least 1 second. "Stop" is displayed. 4 Start Calibration of horizontal direction Press the Control knob. Once "Move Forward" appears on the display, the vehicle must be advanced. 5 Start Calibration of straight direction When the vehicle is driven on the straight direction, calibration of straight direction automatically starts. • In order to operate the detection of straight direction. When the Calibration is finished, "Calibration OK" is displayed. • If you fail to complete the calibraton, "No Calibration" is displayed. In such a case, repeats step 1 thru 6. 6 Exit G-Analyzer Calibration set mode Press the [MENU] button. 38 | English Menu system Function of the KDC-W7031 G-Analyzer Stop Watch The control of stop watch can be started by GAnalyzer function. • Do not use G-Analyzer stop watch on the Public roads. 1 Select G-Analyzer Stop Watch mode Push the Control knob ...
