Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Recalling equalizer curves There are six stored equalizer curves which you can easily recall at any time. Here is a list of the equalizer curves: Display Equalizer curve SPR-BASS Super bass POWERFUL Powerful NATURAL Natural VOCAL Vocal CUSTOM Custom EQ FLAT Flat • CUSTOM is an adjusted equalizer curve that you create. • When EQ FLAT is selected no supplement or correction is made to the sound. This is useful to check the effect of the equalizer curves by switching alternatively between EQ FLAT and a set equalizer curve. Press EQ to select the equalizer. • If the equalizer has been previously set to an equalizer curve other than POWERFUL then the title of that previously selected equalizer curve will be displayed, such as SPR-BASS, NATURAL, VOCAL, CUSTOM, or EQ FLAT. Adjusting equalizer curves You can adjust the currently selected equalizer curve setting as desired. Adjusted equalizer curve settings are memorized in CUSTOM. 1 Press AUDIO to select the equalizer mode. Press AUDIO until EQ-L/EQ-M/EQ-H appears in the display. 2 Select the band you want to adjust with the 2/3. EQ-L (low) —EQ-M (mid) —EQ-H (high) 3 Press 5 or . to adjust the equalizer curve. Each press of 5 or . increases or decreases the equalizer curve respectively. • +6 – –6 is displayed as the equalizer curve is increased or decreased. • The actual range of the adjustments are different depending on which equalizer curve is selected. Note • If you make adjustments when a curve other than CUSTOM is selected, the newly adjusted curve will replace the previous curve. Then a new curve with CUSTOM appears on the display while selecting the equalizer curve. Adjusting loudness Loudness compensates for deficiencies in the low- and high-sound ranges at low volume. 1 Press AUDIO to select LOUD. Press AUDIO until LOUD appears in the display. 15 En Audio Adjustments 2 Select LOUD on or off with 5/.. 3 Select the desired level with 2/3. LOW (low) —MID (mid) —HI (high) Note • You can also switch LOUD on or off by pressing the LOUDNESS. Front image enhancer (FIE) The F.I.E. (Front Image Enhancer) function is a simple method of enhancing front imaging by cutting mid- and high-range frequency output from the rear speakers, limiting their output to low-range frequencies. You can select the frequency you want to cut. Precaution • When the F.I.E. function is deactivated, the rear speakers output sound of all frequencies, not just bass sounds. Reduce the volume before disengaging F.I.E. to prevent a sudden increase in volume. 1 Press AUDIO to select FIE. Press AUDIO until FIE appears in the display. 2 Select FIE on or off with 5/.. 3 Select the desired frequency with 2/3. 100—160—250 (Hz) Notes • After switching the F.I.E. function ON, select the Fader/Balance mode in the Audio Menu, and adjust front and rear speaker volume levels until they are balanced. • Switch the F.I.E. function OFF when using a 2speaker system. Adjusting source levels SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. • Settings are based on the volume level of the FM tuner, which remains unchanged. 1 Compare the FM tuner volume level with the level of the source you wish to adjust. 2 Press AUDIO to select SLA. Press AUDIO until SLA appears in the display. 3 Press 5 or . to adjust the source volume. Each press of 5 or . increases or decreases the source volume. • SLA +4 – SLA –4 is displayed as the source volume is increased or decreased. Notes • Since the FM tuner volume is the control, it is not possible to apply source level adjustments to the FM tuner. • The MW/LW tuner volume level can also be adjusted with source level adjustments. English En 16 Initial Settings Adjusting initial settings Initial settings lets you perform initial set up of different settings for this unit. 1 Press SOURCE and hold until the unit turns off. 2 Press AUDIO and hold until STEP appears in the display. Press AUDIO repeatedly to switch between the following settings: STEP—A-PI Use the following instructions to operate each particular setting. • To cancel initial settings, press BAND. • You can also cancel initial settings by holding down AUDIO until the unit turns off. Setting the FM tuning step Normally the FM tuning step employed by seek tuning is 50 kHz. When AF or TA are on the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. 1 Press AUDIO to select STEP. Press AUDIO repeatedly until STEP appears in the display. 2 Select the FM tuning step with 2/3. Pressing 2/3 will switch the FM tuning step between 50 kHz and 100 kHz while AF or TA is on. The selected FM tuning step will appear in the display. Note • The tuning step remains at 50 kHz during manual tuning. Switching Auto PI Seek The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press AUDIO to select A-PI. Press AUDIO repeatedly unti...
Este manual também é adequado para os modelos :Unidade - DEH-2460R (1022.45 kb)
Unidade - DEH-3400R (1022.45 kb)