Assessments - 11, GPA: 4.2
(
)
)
|
Fotos e especificações Sony CDX-GT317EE |
Facilidade de uso
178 x 50 x 179 mm (7 1/8 x 2 x 7 1/8 in) (w/h/d) Mounting dimensions: Approx. 182 x 53 x 162 mm (7 1/4 x 2 1/8 x 6 1/2 in) (w/h/d) Mass: Approx. 1.2 kg (2 lb 11 oz) Supplied accessories: Card remote commander: RM-X151 Parts for installation and connections (1 set) Optional accessories/equipment: BUS cable (supplied with an RCA pin cord): RC-61 (1 m), RC-62 (2 m) CD changer (10 discs): CDX-757MX CD changer (6 discs): CDX-T70MX, CDX-T69 Source selector: XA-C40 AUX-IN selector: XA-300 Interface adaptor for iPod: XA-110IP Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Design and specifications are subject to change without notice. • Halogenated flame retardants are not used in the certain printed wiring boards. • Halogenated flame retardants are not used in cabinets. • Paper is used for the packaging cushions. • VOC (Volatile Organic Compound)-free vegetable oil based ink is used for printing the carton. 16 Troubleshooting CD/MD playback The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. • If the unit is turned off and the display disappears, it cannot be operated with the remote commander. —► Turn on the unit. The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box. No sound. • The volume is too low. • The ATT function is activated, or the Telephone ATT function (when the interface cable of a car telephone is connected to the ATT lead) is activated. • The position of the fader control “FAD” is not set for a 2-speaker system. • The CD changer is incompatible with the disc format (MP3/WMA). — Play back with a Sony MP3 compatible CD changer, or this unit. No beep sound. • The beep sound is canceled (page 11). • An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. • The RESET button has been pressed. — Store again into the memory. • The power supply lead or battery has been disconnected. • The power supply lead is not connected properly. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition is switched. The leads are not matched correctly with the car’s accessory power connector. The display disappears from/does not appear in the display window. • The dimmer is set “DIM-ON” (page 11). • The display disappears if you press and hold (OFF). —— Press and hold (OFF) on the unit until the display appears. • The connectors are dirty (page 15). The Auto Off function does not operate. The unit is turned on. The Auto Off function activates after turning off the unit. — Turn off the unit. Card remote commander operation is not possible. Make sure the insulation film has been removed (page 4)._ The disc cannot be loaded. • Another disc is already loaded. • The disc has been forcibly inserted upside down or in the wrong way. The disc does not playback. • Defective or dirty disc. • The CD-Rs/CD-RWs are not for audio use (page 14). MP3/WMA files cannot be played back. The disc is incompatible with the MP3/WMA format and version (page 14). MP3/WMA files take longer to play back than others. The following discs take a longer time to start playback. - a disc recorded with a complicated tree structure. - a disc recorded in Multi Session. - a disc to which data can be added. The display items do not scroll. • For discs with very many characters, those may not scroll. • “A.SCRL” is set to “OFF”. —— Set “A.SCRL-ON” (page 12) or press (SCRL) on the card remote commander. The sound skips. • Installation is not correct. —— Install the unit at an angle of less than 45° in a sturdy part of the car. • Defective or dirty disc. The operation buttons do not function. The disc will not eject. Press the RESET button (page 4). Radio reception The stations cannot be received. The sound is hampered by noises. • Connect a power antenna (aerial) control lead (blue) or accessory power supply lead (red) to the power supply lead of a car’s antenna (aerial) booster (only when your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass). • Check the connection of the car antenna (aerial). • The auto antenna (aerial) will not go up. — Check the connection of the power antenna (aerial) control lead. • Check the frequency. Preset tuning is not possible. • Store the correct frequency in the memory. • The broadcast signal is too weak. Automatic tuning is not possible. • Setting of the local seek mode is not correct. — Tuning stops too frequently: Set “LOCAL-ON” (page 12). — Tuning does not stop at a station: Set “MONO-ON” (page 12). • The broadcast signal is too weak. — Perform manual tuning. General No powe...