Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Please have the wiring connection of the power supply, speakers and antenna as for the requirement of the manual, and then install the metal sliding housing into the car according to the diagram. METAL SUPPORT STARP To further improve the ant-skip system please secure the metal strap firmly to Bend the tabs on the metal mounting sleeve against the DASHBOARD with a screwdriver. DASHBOARD METAL MOUNTING SLEEVE To remove the unit out of the metal mounting sleeve, insert the two supplied KEYS into the left and right side slots of the chassis at the same time. Then pull the chassis out of the metal mounting sleeve as shown in the right illustration. PLASTIC TRIM RING FRONT PANEL 6 Connection diagram Notes: VIOLET / BLACK In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. Prohibit to make the conductors of auto antenna and ground touch with each other. 8 Panel controls 1. RELEASE button 2. CLOCK button 3. CD slot 4. EJECT button 5. MODE button 6. PTY button 7. BAND button 8. AUX in 21 9. PREVIOUS/NEXT button 20 10. MUTE button 11. APS button 12.6/10 UP button 13.5/10 DN button 14.4/RDM button 15. 3/RPT button 16. 2/INT button 17. 1/TOP/PLAY/PAUSE button 18. VOLUME/SEL knob 19. POWER button 20. AF button 21.TA button 1 2 3 4 5 19 18 17 16 15 14 13 12 11 10 9 CD f'-OOCn General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press RELEASE button and remove the front panel, then press RESET button on the inner panel to restore the unit to the original factory settings. Power button Press any button (except RELEASE button) to turn on the unit. Press and hold POWER button to turn off the unit. Mode setting Press MODE button to change playing mode in the sequence: RADIO => CD (if there is a disc in unit) = > AUX. Volume control Rotate VOLUME knob to adjust volume level. Turning the sound off When the power is on, press MUTE button to turn the sound off. Press it again or rotate VOLUME knob to turn the sound on. 10 Setting the clock • To show the time: - In Radio mode when RDS data is received press CLOCK button to select the mode: CLOCK = > PTY => FREQUENCY => PS NAME. - In Radio mode when RDS data is not received press CLOCK button to select the item: CLOCK = > PTY => FREQUENCY. - In Disc mode: Press CLOCK button shortly to display time for 5 seconds. • To adjust the time: - When time is displayed, press and hold for 2 seconds CLOCK button. Time will start blinking. - Rotate VOLUME knob clockwise to adjust minute. - Rotate VOLUME knob anticlockwise to adjust hour. - Press CLOCK button again to save setting. Setting the sound characteristics Press shortly and repeatedly SEL button to select the audio parameter: VOL => BASS => TREBLE = > BALANCE => FADER. Rotate VOLUME knob to adjust the selected parameter. Note: If turning off the power, all the settings of each mode will be saved. If you don't rotate VOLUME knob within 3 seconds after selecting the desired parameter, the unit will automatically return to the current mode being displayed. Setting other characteristics Press and hold for 2 seconds SEL button to enter the setting mode. Press repeatedly SEL button to select the setting: TA SEEK/TA ALARM, PI SOUND/PI MUTE, RETUNE L/RETUNE S, MASK DPI/MASK ALL, BEEP 2ND/BEEP ALL/BEEP OFF, SEEK1/SEEK2 (in 11 RADIO mode), DSP (FLAT/CLAS/ROCK/POP), LOUD OFF/LOUD ON, STEREO/MONO (in RADIO mode), DX/LOCAL (in RADIO mode), VOL LAST/VOL ADJUST, ESP6/ESP25. Rotate VOLUME knob to set the parameter. Press SEL button to confirm the setting. - TA SEEK/TA ALARM: TA seek: when newly tuned station does not receive TP information for 60 seconds, the radio retunes to next station which has not the same station (PI) as the last station, but has the TP information. When TP information gets lost at the current station for retune time selected (60 or 90 seconds), the radio start to retune to next same PI station. When same PI station does not catch in 1 cyclic search, the radio retunes to next station with TP information. TA alarm: when this mode is selected, any automatic retune mode is not activated. Only double beep sound (ALARM) is output. When newly tuned station does not have TP information for 5 seconds, a beep comes out. When TP information is missing from the current station for retune time, beeps will be heard. When newly tuned station does not have RDS signal, PI SEEK will pause. - PI SOUND/PI MUTE: PI sound: If a car is cruising between buildings, an oscillation phenomenon may occur, due to different PI codes being received from the same AF. PI mute: In above situation, the sound will be muted for less than 1 second. - RETUNE L/RETUNE S: The initial time of automatic TA search or PI SEARCH mode is selected. When PI information is not received for retune time, the radio will search for the next, s...