Log:
Assessments - 3, GPA: 3.7 ( )

Instruções de Operação Vitek, Modelo VT-3625

Fabricante : Vitek
Arquivo Tamanho: 1.07 mb
Arquivo Nome : Vitek-VT-3625-Pdf-Rus.Pdf
Língua de Ensino: ruukende
Ir para baixar



Facilidade de uso


1 -4) Note: Store the key in a reliable place as you may need to remove the device from the car in the future. Removal and installation of the front panel The front panel of this device can be removed in order to avoid theft. Removing the front panel Press the (4) button (17) in order to make it possible for the front panel to move into the horizontal position (PIC. 5). Press the button on the back side of the panel and pull forward in order to disconnect the panel and carefully remove the panel from its holding bracket (PIC. 6). Place the front panel into the protective case supplied with the radio for safekeeping (PIC. 7). Be careful when handling the front panel! 1. Do not drop the front panel 2. Do not press on the screen during installation and removal. 3. Do not touch the contacts on the panel or the main device - that can lead to poor electrical contact. 4. Dirt or foreign matter should be removed with a clean, dry cloth. 5. Do not subject the panel to heat or direct sunlight. 6. Do not allow the panel to come into contact with flammable substances or solvents. 7. Do not attempt to take the front panel apart. Installing the front panel back into place (PIC. 8) After the holding bracket returns to its initial (vertical) position, place the front panel into the bracket. Place one side of the front panel into the proper position and then press the other side of the panel into position until you hear it “click.” Note: If the panel is installed in the wrong position, several regulators may not work and parts of the display will not light. If this happens press the (&) button and reinstall the front panel. 4 3625_41.qxd 29.03.05 16:39 Page 5 -Q- ENGLISH ISO TYPE CONNECTOR RCA jacks: Line out: : Red (right) : White (left) Line in: : Red (right) : White (left) PLUG A 3. 4. Memory+12 V 5. Car Antenna Output 6. 7. +12 V (to ignition switch) 8. Ground (-) Note: (Plug A contact number 7) should be connected to the ignition switch of the car in order to avoid discharging of the car battery when the engine is turned off and the battery is not being recharged. PLUG B 1. Right rear speaker (+ 2. Right rear speaker (- 3. Right front speaker (+ 4. Right front speaker (- 5. Left front speaker 6. Left front speaker 7. Left rear speaker 8. Left rear speaker (2) momentarily until the desired function appears on the screen. Figure 1 shows the order in which sound control functions are selected using the SEL button. Fig. 1 Sound control function selection 1. Volume 2. Selection 3. Bass 4. Treble 5. Balance 6. Fader adjustment Rotate the knob to set the Bass, Treble, Channel Balance and Fader level. TA SEEK/TA ALARM (2) Press the SEL button for more than 2 seconds to activate the function selector for traffic notification messages. The TA SEEK or TA ALARM functions can be chosen by rotating the VOL knob. ( SEL ]—fTASEEK JgkTAttEK/T AALABMH TA SEEK mode: If a newly tuned station does not transmit traffic information within 5 seconds, the radio automatically tunes to the next station that transmits traffic information. In TA search mode, the current station can be switched to another station if the signal is weak, because the device is searching for TP-stations that have strong broadcast signals and are transmitting TP-signal information. Maintenance REPLACING THE FUSE If the fuse burns out, check the connection to power and replace the fuse. If the fuse burns out again after being replaced then there may be and internal malfunction. If this happens, consult with your nearest service center. Warning Use a fuse of the indicated current level for each wire. Using fuses with high current levels can lead to serious damage. Operating Instructions 1. On/Off (


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias