Assessments - 4, GPA: 4.3 ( )

Fabricante : Sony Arquivo Tamanho: 2.37 mb Arquivo Nome : Língua de Ensino:

However, this is not a sign of malfunction. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer. To maintain high quality sound Be careful not to splash juice or other soft drinks onto the unit or tapes. Cassette care • Do not touch the tape surface of a cassette, as any dirt or dust will contaminate the heads. • Keep cassettes away from equipment with built-in magnets such as speakers and amplifiers, as erasure or distortion on the recorded tape could occur. • Do not expose cassettes to direct sunlight, extremely cold temperatures, or moisture. • Slack in the tape may cause the tape to be caught in the machine. Before you insert the tape, use a pencil or similar object to turn the reel and take up any slack. Distorted cassettes and loose labels can cause problems when inserting or ejecting tapes. Remove or replace loose labels. The sound may become distorted while playing the cassette. The cassette player head should be cleaned after each 50 hours of use. The use of cassettes longer than 90 minutes is not recommended except for long continuous play The tape used for these cassettes is very thin and tends to stretch easily. Frequent playing and stopping of these tapes may cause them to become entangled in the cassette deck mechanism. 6 Getting Started Resetting the unit Before operating the unit for the first time or after replacing the car battery, you must reset the unit. Remove the front panel and press the RESET button with a pointed object, such as a ballpoint pen. f □ RESET button Note Pressing the RESET button will erase the clock setting and some stored contents. Detaching the front panel You can detach the front panel of this unit to protect the unit from being stolen. Caution alarm If you turn the ignition switch to the OFF position without removing the front panel, the caution alarm will beep for a few seconds. If you connect an optional amplifier and do not use the built-in amplifier, the beep sound will be deactivated. 1 2 Press (OFF)*. Tape playback or radio reception stops (the key illumination and display remain on). * If your car has no ACC position on the ignition switch, be sure to turn the unit off by pressing ( off) for 2 seconds to avoid car battery drain. Press (open), then slide the front panel to the right, and gently pull out the left end of the front panel. Notes • If you detach the panel while the unit is still turned on, the power will turn off automatically to prevent the speakers from being damaged. • Do not drop or put excessive pressure on the front panel and its display window. • Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in parked cars or on dashboards/rear trays. Tip When carrying the front panel with you, use the supplied front panel case. continue to next page t 7 Attaching the front panel Place hole A of the front panel onto the spindle ® on the unit, then lightly push the left side in. x Note Do not put anything on the inner surface of the front panel. Setting the clock The clock uses a 24-hour digital indication. Example: To set the clock to 10:08 1 Press (menu), then press either side of (disc/preset) or (preset) repeatedly until “CLOCK” appears. 5EJ r 1 nr v * LLULh ENTER o Press (ENTER). The hour indication flashes. 2 Press either side of (disc/preset) or (preset) to set the hour. 3 Press the (+) side of (seek). The minute indication flashes. O Press either side of (disc/preset) or (preset) to set the minute. 2 Press (ENTER). I in run _IIJUJU_ The clock starts. After the clock setting is completed, the display returns to normal play mode. Tips • You can set the clock automatically with the RDS feature (page 15). • When D.INFO mode is set to ON, the time is always displayed (page 18). 8 Cassette Player Playing a tape in various modes Listening to a tape 1 Press (open) and insert a cassette. Playback starts automatically. 2 Close the front panel. If a cassette is already inserted, press (SOURCE) repeatedly until “FORWARD” or “REVERSE” appears to start playback. FORWARD: The side facing up is played. REVERSE: The side facing down is played. To Press Change the tape’s (MODE) (^O) playback direction Stop playback (OFF) Eject the cassette (OPEN) then Z Skip tracks (SEEK) (^^/^H) - Automatic [once for each track] Music Sensor Fast-forward/ (SEEK) (m/M) reverse [hold to desired point] - Manual Search Note The AMS function may not work when: - the blanks between tracks are shorter than 4 seconds. - there is noise between tracks. - there are long sections of low volume or quiet sections. You can play the tape in various modes: • METAL lets you play a metal or CrO2 tape. • BL.SKP (Blank Skip) skips blanks longer than 8 seconds. • ATA (Automatic Tuner Activation) turns on the tuner automatically when fast-winding the tape. 1 During tape playback, press ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :