Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
E
E
Installation Guide
N
(continued)
N
G
G
L
L
I
I
S
Power Lead
ready to begin connecting them to the LCD monitor wires.
S
❏ Final Installation
H
If your car has a radio or is pre-wired for one:
The wiring diagram (a page 84-93) shows the proper con-
H
Lead Connections
Cut the connector wires one at a time from the plug (leav-
nections and color coding of the leads.
67
Connect all wires, making sure that each connection is
68
ing the leads as long as possible) so that you can work with
We strongly recommend that you test the unit before mak-
insulated and secure. Bundle all loose wires and fasten
individual leads. Turn the ignition on to the accessory posi-
ing a final installation.
less than 30°
them with tape so they will not fall down later. Now insert
tion, and ground one lead of the test bulb to the chassis.
You can set the unit on the floor and make temporary con-
the LCD monitor into the mounting collar.
nections to test the unit. Use electrical tape to cover all
exposed wires.
Congratulations! After making a few final checks, you’re
ready to enjoy your new LCD monitor.
Important: Connect the red power lead last, after you
Caution: Do not disconnect the battery terminals of a
have made and insulated all other connections.
car with trip or navigational computer since all user set-
tings stored in memory will be lost. Instead take extra
Touch the other lead of the test bulb to each of the exposed
❏ Final Checks
care with installing the unit to prevent shorts.
wires from the cut radio connector plug. Touch one wire at a
1. Make sure that all wires are properly connected and
time until you find the outlet that causes the test bulb to light.
Ground
insulated.
This unit should be professionally installed. In case of diffi-
Connect the black ground lead of the power connector to
2. Make sure that the LCD monitor is securely held in
culty, please consult with your nearest professional
Now turn the ignition off and then on. If the bulb also turns
the metal car chassis.
the mounting collar.
installer.
off and on, that outlet is the car power lead.
3. Turn on the ignition to check the unit for proper
1. This unit only operates in a 12-volt DC negative ground
Speakers (not supplied speaker)
operation.
system.
If your car is not wired for an audio unit:
Connect the speaker wires. See the wiring diagram for the
2. Follow the electrical connections carefully (a page 84-
Go to the fuse block and find the fuse port for radio
proper hookups. Follow the diagram carefully to avoid
If you have difficulties, consult your nearest authorized pro-
93). Failure to do so may result in damage to the unit.
(RADIO) accessory (ACC) or ignition (IGN).
damaging the speakers and the stereo unit.
fessional installer for assistance.
3. Connect the power lead after all other connections are
The speakers used must be able to handle more than 45 W
made.
Battery Lead
of audio power. If using an optional audio power, the speak-
❏ Precautions
4. Be sure to connect the battery lead (yellow) to the posi-
If your stereo unit has a yellow lead, you will need to locate
ers should be able to handle the maximum amplifier output
tive terminal (+) of the battery or fuse block (BAT) termi-
the car's battery lead. Otherwise you may ignore this pro-
power. Speakers with low input ratings can be damaged.
nal.
Cautions:
cedure. (The yellow battery lead provides continuous power
Speaker impedance should measure 4–8 Ω, which is typi-
5. Insulate all exposed wires to prevent short circuiting.
¡We strongly recommend that you wear gloves for
to maintain a clock or other functions.)
cally marked on most speakers. Lower or higher imped-
6. Secure all loose wires after installing the unit.
installation work to protect yourself from injuries.
ance speakers will affect output and can cause both speak-
¡When bending the mounting tab of the mounting col-
7. Please carefully read the operating and installation
If your car has a radio or is pre-wired for one:
er and stereo unit damage.
lar with a screwdriver, be careful not to injure your
instructions of the respective equipment before connect-
With the ignition and headlights off, identify the car battery
hands and fingers.
ing it to this unit.
lead by grounding one lead of the test bulb to the chassis
Caution: Never ground the speaker cords. For exam-
ple, do not use a chassis ground system or a three-wire
and checking the remaining exposed wires from the cut
¡Disconnect the cable from the negative (–) battery termi-
Caution: Please follow the laws and regulations of
speaker common system. Each speaker must be con-
radio connector plug.
nal (see caution at right).
your state, province or country for installation of the
nected separately using parallel insulated wires. If in
¡Unit should be installed in a horizontal position with the
unit.
doubt about how your car’s speakers are wired, please
If your car is not wired for an audio unit:
consult with your nearest professional installer.
front end up at a convenient angle, but less than 30°.
Go to the fuse block and find the fuse port for the battery,
usually marked BAT.
Battery
Speakers (not supplied speaker)
Connect the yellow battery lead to the correct radio wire or
Identify the car speaker leads. There are two leads for each
to the battery fuse port on the fuse block.
❏ Transportation Bracket Removal
speaker, usually color coded.
Be sure to remove the transportation brackets before use (installation).
Binding-Head
Screws
Use Binding-Head Screws (M5 x 6 mm) for installation. (a page 78)
A handy way to identify the speaker leads and the speaker
Equipment
(M5 x 6 mm)
Be careful not to lose these Binding-Head Screws.
they are connected with is to test the leads using a 1.5 V
Connect any optional equipment according to the instruc-
Transportation
AA battery as follows.
tions furnished with the equipment. Read the operating and
Bracket
Display Unit
Hold one lead against one pole of the battery and stroke the
installation instructions of any equipment you will connect
other lead across the other pole. You will hear a scraping
to this unit.
Transportation
Bracket
sound in a speaker if you are holding a speaker lead.
If not, keep testing different lead combinations until you
Power
Binding-Head
Screws
have located all the speaker leads. When you label them,
Connect the red power lead to the correct car radio wire or
(M5 x 6 mm)
include the speaker location for each.
to the appropriate fuse port on the fuse block.
If the LCD monitor functions properly with all these con-
❏ Connect All Leads
nections made, disconnect the wires and proceed to the
final installation.
Now that you have identified all the wires in the car, you're
76
77
CQ-VAD9300U
CQ-VAD9300U
...