Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
E
E
Installation Guide
N
(continued)
N
G
G
L
L
I
I
S
ous power to maintain a clock or other functions.)
Speaker impedance should measure 4–8 Ω, which is typi-
S
❏ Precautions
H
Caution: Various settings that have been stored in the
H
cally marked on most speakers. Lower or higher imped-
memory in other on-board equipment (car navigation
If your car has a radio or is pre-wired for one:
ance speakers will affect output and can cause both speak-
5
Cautions:
etc.) may be lost if the battery terminals are discon-
6
With the ignition and headlights off, identify the car battery
er and stereo unit damage.
¡We strongly recommend that you wear gloves for
nected.
lead by grounding one lead of the test bulb to the chassis
installation work to protect yourself from injuries.
Therefore, Therefore, we recommend you to make a
and checking the remaining exposed wires from the cut
Caution: Never ground the speaker cords. For exam-
¡When bending the mounting tab of the mounting
record of or to back up the settings before disconnect-
radio connector plug.
ple, do not use a chassis ground system or a three-
collar with a screwdriver, be careful not to injure
ing the terminals.
wire speaker common system. Each speaker must be
your hands and fingers.
After completing installation of the main unit, set up the
connected separately using parallel insulated wires. If
If your car is not wired for an audio unit:
equipment again according to the settings.
in doubt about how your car’s speakers are wired,
¡Disconnect the cable from the negative (–) battery ter-
Go to the fuse block and find the fuse port for the battery,
please consult with your nearest professional installer.
minal (see caution at right).
usually marked BAT.
¡Unit should be installed in a horizontal position with the
This unit should be professionally installed. In case of dif-
front end up at a convenient angle, but less than 30°.
ficulty, please consult with your nearest professional
Speakers (not supplied)
Battery
installer.
Identify the car speaker leads. There are two leads for each
Connect the yellow battery lead to the correct radio wire or
Warning: If your car is equipped with air bag
1. This unit only operates in a 12 V DC negative ground
speaker, usually color coded.
to the battery fuse port on the fuse block.
and/or anti-theft systems, specific procedures
system.
A handy way to identify the speaker leads and the speaker
may be required for connection and disconnec-
2. Follow the Electrical Connections carefully (a page 18-
they are connected with is to test the leads using a 1.5 V
Equipment
tion of the battery to install this product.
27). Failure to do so may result in damage to the unit.
AA battery as follows.
Connect any optional equipment according to the instruc-
Before attempting installation of this electronic
3. Connect the power lead after all other connections are
Hold one lead against one pole of the battery and stroke
tions furnished with the equipment. Read the operating
component against the manufacturer's recom-
made.
the other lead across the other pole. You will hear a scrap-
and installation instructions of any equipment you will
mendation, you must contact your car dealer or
4. Be sure to connect the battery lead (yellow) to the posi-
ing sound in a speaker if you are holding a speaker lead.
tive terminal (+) of the battery or fuse block (BAT) ter-
connect to this unit.
manufacturer to determine the required proce-
If not, keep testing different lead combinations until you
dure and strictly follow their instructions.
minal.
have located all the speaker leads. When you label them,
FAILURE TO FOLLOW THE PROCEDURE MAY
5. Insulate all exposed wires to prevent short circuiting.
Power
include the speaker location for each.
RESULT IN THE UNINTENDED DEPLOYMENT OF
6. Secure all loose wires after installing the unit.
Connect the red power lead to the correct car radio wire or
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
7. Please carefully read the operating and installation
to the appropriate fuse port on the fuse block.
❏ Connect All Leads
SYSTEM RESULTING IN DAMAGE TO THE VEHI-
instructions of the respective equipment before con-
If the LCD monitor functions properly with all these con-
CLE AND PERSONAL INJURY OR DEATH.
necting it to this unit.
Now that you have identified all the wires in the car, you're
nections made, disconnect the wires and proceed to the
ready to begin connecting them to the LCD monitor wires.
final installation.
Caution: Please follow the laws and regulations of
Electrical Connections (a page 18-27) shows the proper
your state, province or country for installation of the
connections and color coding of the leads.
❏ Final Installation
unit.
We strongly recommend that you test the unit before mak-
Lead Connections
ing a final installation.
Connect all wires, making sure that each connection is
less than 30°
You can set the unit on the floor and make temporary con-
insulated and secure. Bundle all loose wires and fasten
nections to test the unit. Use electrical tape to cover all
them with tape so they will not fall down later. Now insert
exposed wires.
the LCD monitor into the mounting collar.
Important: Connect the red power lead last, after you
Congratulations! After making a few final checks, you’re
have made and insulated all other connections.
ready to enjoy your new LCD monitor.
❏ Transportation Bracket Removal
Be sure to remove the transportation brackets before use (installation).
Round Head Screw
Ground
❏ Final Checks
Use Round Head Screws (5 mmø x 6 mm) for installation. (a page 14)
(5 mmø x 6 mm)
Connect the black ground lead of the power connector to
1. Make sure that all wires are properly connected and
Be careful not to lose these Round Head Screws.
Transportation
the metal car chassis.
insulated.
Bracket
Display Unit
2. Make sure that the LCD monitor is securely held in
Transportation
Speakers
Bracket
the mounting collar.
Connect the speaker wires. See the wiring diagram for the
3. Turn on the ignition to check the unit for proper
proper hookups. Follow the diagram carefully to avoid
operation.
Round Head Screw
(5 mmø x 6 mm)
damaging the speakers and the stereo unit.
The speakers used must be able to handle more than 70 W
If you have difficulties, consult your nearest authorized
(Center Speaker: 35W) of audio power. If using an optional
professional installer for assistance.
audio power, the speakers should be able to handle the
maximum amplifier output power. Speakers with low input
ratings can be damaged.
10
11
CQ-VD7700U
CQ-VD7700U
...