Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
E
E
N
Installation Guide (continued)
N
G
G
L
L
I
I
S
S
H
Identify All Leads
Connect All Leads
Final Installation
H
5
The fi rst step in installation is to identify all the car
Now that you have identifi ed all the wires in the car,
Lead Connections
Battery Lead
6
wires you’ll use when hooking up your LCD monitor.
you are ready to begin connecting them to the LCD
Connect all wires, making sure that each connection
If the unit has a yellow lead, you will need to locate
As you identify each wire, we suggest that you label it
monitor wires. The wiring diagram (page 36) shows
is insulated and secure. Bundle all loose wires and
the car’s battery lead. Otherwise you may ignore
using masking tape and a permanent marker. This will
the proper connections and color coding of the
fasten them with tape so they will not fall down
this procedure. (The yellow battery lead provides
help avoid confusion when making connections later.
leads.
later.
continuous power to maintain a clock, memory
We strongly recommend that you test the unit
storage, or other function.)
Congratulations! After making a few fi nal checks,
before making a fi nal installation.
Caution:
you’re ready to enjoy your new LCD monitor.
If your car has a radio or is pre-wired for one:
You can set the unit on the fl oor and make
≥ Do not connect the power connector to the
With the ignition and headlights off, identify the car
temporary connections to test the unit. Use
unit until the wiring is completed. If there are
battery lead by grounding one lead of the test bulb
electrical tape to cover all exposed wires.
no plastic caps on the stereo hooking wires,
to the chassis and checking the remaining exposed
insulate all exposed leads with electrical
Final Checks
wires from the cut radio connector plug.
IMPORTANT:
tape until you are ready to use them. Identify
≥ Connect the red power lead last, after
1. Make sure that all wires are properly connected
the leads in the following order.
If your car is not wired for an audio unit:
you have made and insulated all other
and insulated.
Go to the fuse block and fi nd the fuse port for the
connections.
2. Turn on the ignition to check the unit for proper
battery, usually marked BAT.
operation.
Power Lead
If your car has a radio or is
Dome light lead
Power lead
If you have diffi culties, consult your nearest
pre-wired for one:
The dome light lead connection varies depending on
Connect the red power lead to the correct car radio
authorized professional installer for assistance.
Cut the connector wires
the type of vehicle. Consult your dealer or service
wire or to the appropriate fuse port on the fuse
one at a time from the plug
technician.
block. If the LCD monitor functions properly with all
(leaving the leads as long
these connections made, disconnect the wires and
as possible) so that you can
proceed to the fi nal installation.
work with individual leads.
Turn the ignition on to the accessory position, and
Battery lead
ground one lead of the test bulb to the chassis.
Connect the yellow battery lead to the correct radio
wire or to the battery fuse port on the fuse block.
Touch the other lead of the test bulb to each of the
exposed wires from the cut radio connector plug.
Ground lead
Touch one wire at a time until you fi nd the outlet
Connect the black ground lead of the power
that causes the test bulb to light.
connector to the metal car chassis.
Now turn the ignition off and then on. If the bulb also
turns off and on, that outlet is the car power lead.
Equipment
Connect any optional equipment according to the
If your car is not wired for an audio unit:
instructions furnished with the equipment. Read
Go to the fuse block and fi nd the fuse port for radio
the operating and installation instructions of any
(RADIO), accessory (ACC), or ignition (IGN).
equipment you will connect to this unit.
24
CY-VHD9500U
CY-VHD9500U
25
...