Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
ANY number is pressed in darkness this feature allows user to press ANY number before entering the 4-digit code Power Supply: Operates from the garage door opener power with a battery b&ck-up for code memory and light-IMPORTANT NOTE: When illumination is needed, ed keyboard Unit wiU not operate without battery avoid pressing keyboard area which contains the first code number. DISCONNECT THE POWER TO THE GARAGE DOOR OPENER BEFORE BEGINNING INSTALLATION. STEP 1--SECTIONAL DOORS: Draw two intersecting lines STEP 1--ONE-PIECE DOORS: install the keyboard on the on garage jamb face--horizontally at eye level and vertically exterior front wal! of a FRAME garage Position it away from as close to centedine as possibfe Make sum there is at least the door opening to avoid injury as door swings out and up 1-t/4" clearance on each side of the vertical line. Drill a Drill a 1" diameter hole through wall at eye level Refer to note 1" diameter hole through the jamb at marked location. below; then proceed to Step 2 Refer to illustration on Side 2 if your garage has a built_ up jamb. Garage riot Keyboard Optional Location Doer Jamb Edge NOTE: If garage is Constructed of material other than wood (brick, stone or aluminum siding), install keyboard PARTS LIST on door jamb with this BOARD ON OUTSIDE important exception: LOCATE KEYEDGE OF DOOR JAMB TO AVOID Conso}e Assembly 41D2940 INJURY AS DOOR SWINGS OUT AND UP_ Keyboard Assembly ,HD2952 9 Volt Battery 10A13 NO USER SERVICEABLE PARTS. 2 Strand Betl Wire Transformer Kit (inc , , bel! , wire) 219A276 41A3468 For repair, contact a SEARS Service Center Side 1 NOTE: if your garage has a built up jamb, drill the hole 2" deep. Then, on inside edge of jamb, drill a second hole into first hole to complete access_ l/8" Pilot Hole I _'_--_ "4 1"V.i,--..__'_. fjfq..... 1" Dia Hole N \,J,_\"_ t_._"-_JII 1J I1_", I CabLe r 1 Screw II IL!III!IM ooo, --_ I I I IIit tl rlnsi,deEdge STEP 2: Hold keyboard firmly with the back of the case UP. Position thumb against bottom of case and pull up sharply Keyboard will lift out of cover, allowing access to bottom mounting hole Guide the keyboard cable through hole to inside of garage. Position the keyboard against outside jamb Drill two 1/8" pilot holes for fastening screws Attach securely with (2) 6ABx1-1/4" screws CIose cover Excess cable can be folded and inserted into the access ho_e to keep it out of the way Bell Wife Transformer (To Garage TerminaJs Doer Opener) Con ne,;,"l_O r Guides Kit 4'_A3468 Cable To 120V Ou#et STEP 3: Connect the 2-strand bell wire to terminals labeled 1 and 2 on back of console, insert keyboard cable connector into slot on side of console Be sum connector guides are facing BACK of consote. IMPORTANT; Some garage door openers have a third screw terminal which supplies power to the radio control. This terminal can be connected to terminal No. 3 on the console with a third strand of bell wire (not supplied). With any garage door opener made by Stanley, accessory transformer kit 41A3468 MUST be installed. TRANSFORMER INSTALLATION INSTRUCTIONS: Connect one end of the 2-strand bell wire supplied with the kit to each of the transformer terminals Polarity is not imporlant Con nect the other end of bell wire to terminals 1 and 3 on the Touch Code console. IF THIS ACCESSORY IS USED WITH ANY GARAGE DOOR OPENER OTHER THAN SEARS OR CHAMBERLAIN AND THE BATTERY FAILS IN TWO MONTHS, TRANSFORMER MUST BE INSTALLED° Follow instructions above. STEP 4: Position console on an interior garage wall approximately one foot from outside edge of door. Fasten with (2) 8ABxl" screws Run bell wire up wall and across ceiling to garage door opener terminals Use insulated staples to secure wire Cut off any excess wire Connect to terminals used for push button controls On Sears models, connect wire as follows: Model series 53000--to red and white terminals Model 664400-Lto blue and white terminals Modei 664000--to red and black terminals. All other models_to white and white terminals or to the terminals used for wall push button STEP 5: Pry open front panel of console with a coin or screwdriver. Snap a 9 voIt battery onto circuit board connector and drop into console DO NOT replace panel at this time Console Push Button STEP 6: To set code, move programloperate switch near the battery to PROGRAM position (keyboard light should flash) NOTE: If the light does not flash, check the cable and battery connections° Press any four numbers on keyboard CAUTION: For security, do not use address, license or consecutive numbers (1,2,3,4 etc.). Move the programloperate switch to OPERATE position (the keyboard light will go off) Reconnect power to garage door opener If you have installed Transformer Kit 41A3468, plug the transformer into a 120 Volt outlet. Enter the code on the keyboard. If the door operates properfy, replace the front panet on the console Loss of power to either the battery or the garage door opener will not affect the programmed code. However, if BOTH ...