Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Contact door distributor or manufacturer for instructions. HIGH SPRING TENSION Can Cause Serious Injury or Death Repairs or adjustments must be made by a trained service person using proper tools and instructions CHAIN CHAIN BELT BELT PN# 36420Supplement, 10/27/2008 9 1 OPENER ASSEMBLY FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM NOTE: Three (3) piece rail assemblies are for a 7 foot high door. Clear a workspace area to unpack and organize box and contents for assembly. 1. There are 4 boxes inside the carton. Each box is numbered 1 - 4. Note that some openers will contain the same parts and be packaged with fewer boxes. Carefully remove the three internal boxes (Labeled #1, 2, and 3) and place them on the floor for easy access (Fig. 1-1). These boxes contain assembly parts and the contents are organized by assembly tasks. For quick reference inside the lid of each box there is a label illustrating the components inside. 2. Remove the motor power head and place it on the floor for later use. Remove box #4 and place it on the floor for later use. Do NOT run until opener is fully assembled. CAUTION FIG. 1-1 Internal boxes. RAIL ASSEMBLY: Use a clean, flat surface. Rail Connectors Rail Connector Bolts Rail Connector Nuts NOTE Some doors need bracing. Contact door distributor or manufacturer for instructions. HIGH SPRING TENSION Cause Serious Injury or Death ments must be made by a trained roper tools and instructions Bolts Power head Rail Lag Srews 5/16" Nuts & Bolts Header Bracket Bolts Header Bracket Bag 2 Bag 1 Bag 3 Bag 0 Box Label Example #4 1. READ AND FOLLOW ALL SAFETY, INSTALL ATION AND OPERATION INSTRUCTIONS. (If you have questions or do not understand an instruction, call The Genie Company or an authorized Genie® Dealer.) 2. Install only on a properly balanced sectional garage door. An improperly balanced door could cause severe injury. Have a trained door system technician make repairs or adjustments to cables, spring assemblies, and other hardware before installing the opener. 3. Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener. 4. Where possible, install the door opener 7 feet or more above the floor. For products having an emergency release, mount the emergency release 6 feet above the floor. IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: 5. Do NOT connect the opener to source of power until instructed to do so. 6. Locate the control button: • Within sight of door, • At minimum height of 5 feet so small children are not able to reach it, and • Away from all moving parts of the door. 7. Install the Entrapment WARNING Label next to the control button in a prominent location. Install the Emergency Release Tag on or next to the emergency release. 8. After installing the opener, the door must reverse within 2 seconds when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor. To reduce the risk of injury to persons or damage to property - Use this opener only with sectional doors. WARNING NOTE: For 1-piece rail—skip to POWER HEAD & RAIL ASSEMBLY. 10 FIG. 1-2 Split Rail sections. FIG. 1-3 Split Rail assembly. A B Chain Rail Center Rail End Rail Wire Tie(s) Rail Assembly for CHAIN DRIVE OPENER NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. 3. Remove the two rail sections that are not connected to the chain and place them on floor (Fig. 1-2, A). 4. Carefully remove the third rail section with chain and plastic sleeve. Place rail section on floor and extend chain straight out (Fig. 1-2, B). Chain and rail should extend approximately 7 feet. 5. Remove wire ties and plastic bag from chain. Leave chain extended straight out on floor. Avoid kinks in the chain by careful handling and keeping chain flat on the floor. 6. Align the three rail sections by pulling the chain straight and wrapping it around the chain tensioner pulley (Fig. 1-3 & 1-4). 7. Attach the two rail clamps to the rail section joints with (4) bolts and nuts. After both rail clamps have been assembled to the rail sections, securely tighten the bolts and nuts. PN# 36420Supplement, 10/27/2008 Rail Clamps Rail Clamp Bolts Rail Clamp Nuts Rail with chain Center Rail End Rail Chain Trolley Slide Release Knob ng Power Head NOTE Some doors need bracing. Contact door distributor or manufacturer for instructions. HIGH SPRING TENSION Can Cause Serious Injury or Death Repairs or adjustments must be made by a trained service person using proper tools and instructions Rail with belt Center Rail End Rail Belt Release Knob NOTE Some doors need bracing. Contact door distributor or manufacturer for instructions. HIGH SPRING TENSION Can Cause Serious Injury or Death Repairs or adjustments must be made by a trained service person using proper tools and instructions Rail Assembly for BELT DRIVE OPENER NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. 3. Remove the two rail sections that are...
Este manual também é adequado para os modelos :Portão automático - BeltLift 1024 (14.87 mb)
Portão automático - BeltLift 1042 (14.87 mb)