8 2 Program IntelliCode® 2 Remote to Powerhead ............................9 Programming HomeLink®, Car2U®, IntelliCode® 1 remotes or wireless keypads ................................................................................................................10 Reference 3 Typical Installed Illustrations ................................................................ 11-13 Powerhead & Rail Assembled View ............................................................ 11 Typical Sectional Door

Safe-T-Beam® System must be installed to close door. Homelink® and Car2U® compatible. For Answers and Assistance: 1.800.354.3643 or visit WARNING: To reduce the risk of injury to persons or damage to property – Use this opener only with a one piece or sectional door. SAVE THIS MANUAL FOR FUTURE REFERENCE. INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. Genie, Genie logo, Intellicode and Safe-T-Beam are registered trademarks and TriloG is a trademark of GMI holdings, Inc., dba The Genie Company. Hom

Genie, Intellicode, Safe-T-Beam and the Genie logo are registered trademarks and TriloG, GenieSense and Sure-Lock are trademarks of GMI Holdings, Inc., d/b/a The Genie Company. Consistent with our policy of continuing product improvement, we reserve the right to change product specifications without notice or obligation. HomeLink is a registered trademark of Johnson Controls. Car2U is a trademark of Lear Corporation. P900-834 15M 2/11 JAR Standard rail is for use with doors up to 7 feet. Ask you

1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including wall console, remote, or wireless keypad. 3. During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the rail carriage by pulling the Emergency Release Handle. See page 19 for Release Handle operation. LOST OR STOLEN REMOTE - CLEARING MEMORY Clearing rem

Safe-T-Beam® System must be installed to close door. For use only with residential sectional or one piece overhead garage doors. Homelink® and Car2U® compatible. For Answers and Assistance: 1.800.354.3643 or visit WARNING: To reduce the risk of injury to persons or damage to property – Use this opener only with a one piece or sectional door. SAVE THIS MANUAL FOR FUTURE REFERENCE. INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER CHAIN/BELTGARAGE DOOR OPENER MODELS IntelliG™1000/1200, SilentMax™1000/12

1. Door springs and hardware. • Do not operate garage door automatically or TROUBLESHOOTING GUIDE Use This Guide To Correct Problems With Door Operator. manually if springs are broken. If These Solutions Do Not Work, – CONTACT A PROFESSIONAL FOR SERVICE. Call Customer Service at 1.800.35.GENIE 2. Door balance. • Close the door. • Pull emergency release knob down to release door from carriage assembly. • Raise door manually approximately 3 feet. – Door should stay in that position or close very s

The system works with up to seven remotes for one door and features advanced technology that prevents piracy of the radio signal that opens your door. Frequency Range Reliable frequency range to ensure consistent operation. Self-diagnostic Safe-T-Beam® System When objects pass through the infrared beam, the door automatically stops closing, and then reverses. The system's self-diagnostic functions alert homeowners of improper operations and pinpoints specific problems. Light System Illumin

• Check where the door stopped. – Adjust the close limit screw and repeat cycling the door and making adjustments until it fully closes. NOTE If the door is reversing after contacting the floor, the limit is set too far toward the door and needs to be set back. Step 5: ADJUSTING AND TESTING THE FORCE CONTROLS WARNING Too much force will prevent safe operation of the garage door. Someone could be seriously injured or killed if the door force is set too high. A closing door may not reverse properl

The receiver in the GDO’s powerhead can receive signals at 315 AND 390 MHz. The remote is factory set at 315 MHz. See Figure 2 and 3 on page 11 for frequency selector switch. Switch your remote control frequency when: • Remote does not have adequate range. • Remote works inconsistently with fresh battery installed - LED feedback lights up when pressing button. • Programming your car’s HomeLink® system. To program a HomeLink® device: (This GDO is HomeLink® compatible.) • Use a small flat screwdri

2-4). OPEN ORANGE PARTS BAG FIG. 2-4 Adding mounting surface. FIG. 2-5 Header bracket in place (3 methods). FIG. 2-6 Examples of door bracing. FIG. 2-7 Mounting door Bracket (sectional). preferred 1 2 3 FIG. 2-7B Mounting door Bracket (one-piece). bolted to studs in wall even with or above top roller on top edge at top of back 12 2. Mounting the header bracket. NOTE: Although header bracket may be oriented several ways, method 1 is preferred if possible because of added strength over other metho