Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Be sure to drill a 19mm (3/4") diameter hole only. 2. Feed as much cable as possible into vehicle and clamp securely. This reduces the possibility of being hooked during production. 3. Keep all cables away from HOT, ROTATING and ELECTRICALLY NOISY components. 4. To increase protection of cable, place all excess wire and extension cable in convoluted tubing. 5. Do not twist camera cable and do not cut camera pigtail or cable. WIRING MONITOR 1. See wiring diagram for connections to ignition ground and back-up circuit.(See Fig.3) 2. Wiring Monitor: Insert extension cable into camera #1 position if (2) camera are used , be sure to mark each extension cable properly and plug second cable into camera #2 position. Bundle excess cable together using a cable tie or vinyl tape. This will avoid possible damage to cable during ope ration. (See Fig.3) 3. The red wire is connected to an ignition power source, the black wire is connected to chassis ground, and the blue wire is connected to the vehicle's back up circuit.(See Fig.3) 4 voyager VOM-58 OPERATIONS MANUAL FUNCTIONS AND OPERATION Front of Monitor : See FIGURE 4 1. Power switch : STD. BY- Monitor operates when vehicle transmission is switched into "REVERSE" ON - monitor and system operate when ignition switch is "ON" 2. CA1/CA2 switch : "CA1" used mainly for rear mounted camera or as specified by the installer. "CA2" used mainly for side or mirror mounted camera or as specified by the installer. 3. Day/ Night switch : Pre-set brightness and contrast levels optimized for day or night operation. 4. Contrast : Variable control of contrast. Should be adjusted if the "DAY/ NIGHT" switch does not achieve the most desirable picture. 5. Brightness : Variable control of brightness. Should be adjusted if the "DAY/ NIGHT" switch does not achieve the most desirable picture. 6. Volume : Variable control of internal speaker volume. FUNCTIONS AND OPERATION CONTINUED Rear of monitor : See FIGURE 4 1. POWER CONNECTION : Pin No. (Description 1 N/C 2 Power ( DC 12V or 24V) 3 Ground 4 N/C 5 Trigger In (DC 12V or 24V) 6 N/C VOM-58 5 VOM-58 OPERATIONS MANUAL 2. MIR/NOR OPTION Monitor switch position in "MIR" position Voyager camera switch (magnet) in "MIR" position - This combination will result in an inverted (mirrored) image that is correct for rear (back-up) camera use. - If the opposite image is required for applications other then rear (back-up) camera use, either the monitor or the camera switch should be set to the "NOR" position. - Make sure that monitor/camera switch settings are correct for your particular application. 3. AUDIO JACK - Connects audio connector to an (optional) external speaker. 4. CA1/CA2 INPUTS JACKS - In single camera applications the camera should be connected to CA1 Monitor Input. - A Rear/Back-up Camera should be connected to CA1 Monitor Input in any application. Reverse trigger Feature Applying +12 Volts to Blue/Reverse Trigger lead serves two functions: 1) Monitor comes ON from Stand-by mode and switches to CA1 input. 2) Monitor Input will switch from CA2 to CA1 while +12 Volts is applied. 6 Voyager VOM-58 OPERATIONS MANUAL AFFIXING DISTANCE MARKERS TO THE MONITOR SCREEN 1. Clean monitor screen surface of fingerprints. Place distance indicators behind the vehicle at (3) feet, (5) feet and (9) feet along the width of the vehicle. These distances are measured from the rear bumper.(Referto fig. 5) 2. Attach the markers to the monitor screen over the images of the distance indicators. These markers represent distances of (3) feet, (6) feet and (9) feet from the back of the vehicle (See fig.5 3. Affix the "STOP" marker on the monitor screen over the image of the rear bumper to locate the rear bumper. 4. The monitor screen is now "calibrated" for distances behind the vehicle of (3) feet, (6) feet and (9) feet. STEEL PLATE FOR REINFORCEMENT (RECOMMENDED FOR SECURE MOUNTING) FIGURE 1 VOM-58 7 VOM-58 OPERATIONS MANUAL MONITOR MOUNTING HOLE PATTERN FIGURE 2 8 Voyager VOM-58 OPERATIONS MANUAL WATERPROOF CAMERA CONNECTOR TO MONITOR \ CAMERA #1 INPUT 20METERS nQpin =13=1 GROMMET TO SEAL THOUGH VEHICLE EXTERIOR REAR OF MONITOR TT™ 1 DOOOOOi Mil ID 1OODDIO r Iddddii H ^