Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
Be extremely careful of seats that have airbags built into them. Keep wiring away from any air bag wiring (usually identified by yellow connectors and yellow wire jackets). Damage to air bag wiring can result in personal injury to vehicle occupants. If you have any questions regarding wire routing or installation in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074. When connecting power and ground in a mobile video installation, insure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product. An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle's parking brake is applied. An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking is not applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to be operator of the motor vehicle. Licensed under one or more of the following patents: Patent NOS. 7,245,274 ,6,899,365 and 6,678,892 FEATURES • 7” Digital TFT (Thin Film Transistor) Active Matrix LCD (Liquid Crystal Display) Monitor • OSD (On Screen Display) for control of picture quality and functions • Two Audio / Video Source inputs (AV and AUX). • Screen mode selection (4:3, 16:9) • Full function remote control • IR headphone (optional) SPECIFICATIONS Type TFT Active Matrix LCD Resolution 480x234 Pixels 336,960 Operation Temperature 32~113°F(0~45° C) Storage Temperature -4 ~149°F (-20 ~ 65° C) Backlit life 20,000 Hours Video Display System NTSC / PAL Headphone Audio Output 0.03W @ 32 ohms Power Source 12VDC Dimension (LxWxH) 147mm x 275mm x 200mm 5.7in x 10.8in x 7.8in Specifications subject to change without notice. AVXMTGHR1M 3 MATERIAL TO USE IN THIS PACKAGE: 1)AVXMTGHR1M System Monitor (AVXMTGHR1M ) NOTE: The AVXMTGHR1M monitor has been designed to be interchangeable from one headrest to the other. The headrests will still have the Red Din cables on them and should be connected to their respective connectors. The headrest cover from the manufacturer is covered with shale colored vinyl. NOTE: Headrest cable is included with the monitor. © ÖÖÖ 1) Remote Control 2)AUXPIGTAIL (P/N 136-5151)-(1pc) (P/N 112B3227 )-(1pc) 3) 8PIN (Male) AV OUT to RCA (P/N 112-4149)-(1pc) uTonnmiJii □o]jmD=QJ aöm»iL 5) Heat Shrink Tube (P/N 138-1495)-(1pc) 4) Support Tube Adaptor Box (P/N 170-0161)-(1box) 4 AVXMTGHR1M HEADREST COVER REPLACEMENT: NOTE: If desired, replace the headrest cover before installing the headrest in the vehicle. 1. Using a Philips screwdriver, unscrew the two Philips screws and lift the bottom edge of the monitor upward. Unscrew Philips Screws 2. Remove the velcro tabs securing the headrest cover. Remove Velcro Tabs 3. Replace the headrest cover with the desired color and secure the headrest cover by re-attaching the velcro tabs. 4.Place the monitor cable into the space on the right side of the headrest and lower the monitor into position to align the two Philips screws with the screw holes in the headrest. Close the screen and press the PUSH button to secure the screen. 5.Tighten screws AVXMTGHR1M 5 VEHICLE PREPARATION 1) Decide on the system configuration and the options that will be installed. 2) Read the manuals and getfamiliarwith the electrical requirements and connections. 3) Decide on the mounting locations and methods of mounting the products that will be connected to the AVXMTGHR1M. 4) Prepare the vehicle by removing any interior trim necessary to gain access to the vehicle's wiring as well as all areas where interconnecting wire harnesses will be located. The mounting method, and the location will vary from vehicle to vehicle, so this manual will only focus for the installation of the AVXMTGHR1M Monitors in the supplied configuration. The best location for the AVXMTGHR1M System components is: a. Monitors: Vehicle specific Headrest NOTE: The Master Monitor should be installed in the passenger position most used.) 5) Locate an accessory power source (+12VDC present when the ignition key is in the accessory and run positions. OVDC should be present when the ignition key is in the OFF position), a constant power source (+12VDC) at all times, regardless of the ignition key and a good ground. Generally, these wires can be found at the ignition switch orfusebox. NOTE: Ensure that both the constant and accessory power is fused...