Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW. THIS IS NOT ONLY DANGEROUS, BUT IT IS ALSO ILLEGAL. 4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure and installation method. Some of the steps that may be required are: A) Removal of the vehicle's dome light. B) The headliner may need to be trimmed. 8 MOUNTING THE VOD80 Figure 2 NOTE: Two of the mounting holes are located under the domelight covers. 9 Trim Ring Installation The Trim Ring Installation is accomplished using the four (4) 2 X 8mm screws supplied. Please refer to the illustration below. 1. Place the VOD80 on a soft surface with the rubber gasket facing up. Use care to avoid scratching the unit’s exterior surface. 2. Place the trim ring on the unit and note the location of the four mounting screws. 3. Remove the four screws that are in the unit. 4. Remove the rubber gasket that is attached to the unit. 5. Attach the trim ring to the unit using the longer four (4) 2 X 8mm screws supplied. 6. Remove the four (4) rubber spacers from the bracket. 10 7. Attach the four (4) post extensions to the bracket. 8. Attach the four (4) rubber spacers on the post extensions 9. Refer to the Owner/Install Manual for the VOD80 to complete the installation. 11 VOD80 Ant enna Y FM Figure 3 1) 2) 3) 4) Make the connections to the vehicle with the 5 pin wiring harness. Connect the 5 pin harness to the mating connector on the Video Monitor. Connect power harness to vehicle's electrical system by tapping into an accessory hot line. Verify all functions of the system before final mounting of the finished assembly. NOTE: A VCP or other A/V Component can be connected to the video monitor system using an RCA A/V cable. This second harness would plug into the AV1 inputs or AUX jack. A/V Source Definitions : 1 = Built-in DVD 2 = AV1 input ( VCP, DVD, etc ) 3 = AV2 Input ( VCP, Game, DVD, etc ) 12 CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, both wires at the dome light will rest at ground. When the light is activated, one of these wires will switch to +12V DC. This is the vehicle's switching wire. On a negative switched system, with all the doors closed and the lights out, both wires at the dome light will rest at + 12V DC. When the light is activated, one of these wires will switch to ground. This is the switching wire. For positive systems, connect the violet / brown (Lamp auto) wire to the vehicle's switched wire. Then connect the red / black (lamp on) wire to a fused constant 12 volt source and the black / red (lamp common) wire to a good ground. Positive systems are commonly found on Ford vehicles. For negative systems, connect the violet / brown (Lamp auto) wire to the vehicle's switched wire. Then connect the red / black (lamp on) wire to a good ground and the black / red (lamp common) wire to fused constant 12 volt source. Negative systems are commonly found on General Motors and import vehicles. Note: Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999 Dodge Caravan, may require that the violet / brown (Lamp auto) wire be connected to the door pin switch wire, as the additional current draw of the Monitor's lights may not be supported by the output of the vehicles body control computer. 13 Positive Switched Dome lighting Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto To 3 pin connector on Monitor To constant +12vdc To constant +12vdc Factory Door ajar Factory Dome light circuit switch or Body Control computer Figure 4 Negative Switched Dome lighting To constant Factory Door ajar Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto To 3 pin connector To constant Factory Dome light circuit switch or Body Figure 5 14 E. Controls, Indicators, and Connectors 1. Unit View (Refer to Figure 6) 1 2 3 4 5 6 7 8 9 10 11 12 13 1415 16 18 17 19 Figure 6 1) FM Modulator Switch 2) AV 2 In Jack 3) Game Port 4) Headphone Jack 5) Power and Dome Light Connector 6) 6pin connector 7) FM Antenna 8) Previous Button 9) Play Button 10) Next Button 11) Disc Insertion Slot 12) Monitor Open Button 13) IR Sensor 14) Eject Button 15) Power Button 16) Stop Button 17) IR Transmitter for Wireless Headphones 18) Auto/Off/On Dome Light Switch 19) Dome Lights 15 2. Remote Control View (Refer to Figure 7) 1) Power Button 2) Display Button 3) Angle Button 4) Subtitle Button 5) A-B Button 6) Slow Button 7) Pause Button 8) Reverse Scan Button 9) Stop Butt...
Este manual também é adequado para os modelos :Vídeo Car - 128-7744 (3.55 mb)