Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
12 Installation and safety notices ......................... 12 Supplied equipment .............. 13 Installation.............................. 13 Connection diagram .............. 17 Features ................................. 19 Specifications ........................ 19 CONTENTS 11 ENGLISH SAFETY INFORMATION General Thank you for deciding to use a Blaupunkt product. We hope you enjoy using this new piece of equipment. Please read these operating instructions before using the equipment for the first time. The Blaupunkt editors are constantly working on making the operating instructions clearer and easier to understand. However, if you still have any questions on how to operate the equipment, please contact your dealer or the telephone hotline for your country. You will find the telephone numbers printed at the back of this booklet. We provide a manufacturer guarantee for our products bought within the European Union. You can view the guarantee conditions at or ask for them directly at: Blaupunkt GmbH Hotline CM/PSS 6 Robert Bosch Str. 200 D-31139 Hildesheim Accessories We recommend you use accessories that have been approved by Blaupunkt. Installation and safety notices Before connecting your signal converter, please read the following information carefully. The battery’s negative terminal must remain disconnected whilst you are installing and connecting the unit. Whilst doing so, you must observe the vehicle manufacturer’s safety notices (airbags, alarm systems, trip computers, immobilizers). Before drilling any holes, you must make sure that no installed cables or vehicle components can be damaged. When installing the signal converter, select a location in the vehicle that allows you to attach it firmly into place using screws. The installation location should be such that the signal converter does not get in the way of the driver and cannot endanger the occupants in the event of the vehicle suddenly coming to a halt, for instance, during an emergency stop. SUPPLIED EQUIPMENT INSTALLATION Supplied equipment The signal converter is supplied with all the parts listed below. Please check that the range of parts supplied with your device is complete. If one of the listed parts is missing, please contact your dealer immediately. . Signal Converter . Connecting cable . RGB adapter . Installation and operating instructions Signal Converter 7 607 003 550 Connecting cable RGB adapter Installation Note: • Before connecting the monitors to your signal converter, check that the +/- and the switched positive are connected properly. After connecting the +/- and the switched positive, the red LED on the signal converter must light up! Positive connection Connect the fuse holder (5A fuse) to protect the positive cable (3) (see Fig. 1). The fuse holder must be connected to the positive terminal at a distance of max. 30 cm from the vehicle battery (if necessary, drill a hole in the bulkhead use the appropriate cable grommets). Switched positive Connect the switched positive cable (4) (see Fig. 1) to the switched positive output ( ) of the main system unit (e.g. car radio or navigation unit). If connecting to the vehicle’s terminal 15, you must connect a fuse holder (1A fuse) to protect the switched positive cable (4) (see Fig. 1). The fuse holder must be connected to the positive terminal at a distance of max. 30 cm from the vehicle battery (if necessary, drill a hole in the bulkhead and use the appropriate cable grommets). Negative (earth) connection Attach the negative cable (1) (see Fig. 1) directly to the vehicle body using a screw. Scratch the surface down to the bare metal at the point at which the earth contact is made and apply graphite grease (important for a good earth connection). 13 ENGLISH INSTALLATION • If the installation requires holes to be drilled or any other changes to the vehicle to be made, please contact a specialist workshop in your area. Note: You cannot display PAL video on the wide vision TV monitor using the RGB input. In this case, the PAL video signal must be connected directly to the AV input of the wide vision TV monitor. 14 12V 12V Earth/GND (1) 1 R1 L1 Monitor Audio in RGB IN DC 12V IN (3) (4) +12V Permanent +12V Fig. 1 INSTALLATION 15 ENGLISH INSTALLATION Video in RGB in Audio in 41 32 R1 R2 R3 R4L1 L2 L3 L4 Monitor Audio in RGB IN DC 12V IN Fuse ( 4 A) RGB out FUSERGB OUT OUTPUT 321 4 Monitors CONNECTION DIAGRAM ENGLISH Signal converter TravelPilot DX 7 607 001 601 / 1,5 m 7 607 001 602 / 4 m RGB adapter 7 607 001 600 7 607 001 601 / 1,5 m 7 607 001 602 / 4 m 12V 17 Various components connected as an example DX-N 12345678 Car Radio Audio R 1 out C1-4x Cinch 7 607 893 093 (0,35m) CONNECTION DIAGRAM RearMonitorRearMonitorRearMonitorRearMonitor CDC-A08IDC-A09CDCout Speakers DVD - Player (IVDP-01)Video out AVin Digitalout Audio L out Audio R out RGB inVideo 4Audio L 4Audio R 4Video 3Audio L 3Audio R 3Video 2Audio L 2Audio R 2Video 1Audio L 1Signal Conver ter (IVSC-5501) M 1...