Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
14 Prepare the working area .............. 14 Mark out the dimensions................ 15 Carefully cut open the headrest cover ............................................. 15 Open the headrest and remove filling and other items ..................... 15 Lay the cable through the headrest ........................................ 16 Insert the mounting frame in the headrest .................................. 16 Insert the monitor .......................... 16 Check and adjust the monitor then apply the Velcro strips ................... 17 Removal ................................. 17 OSD functions........................ 18 Main menu .................................... 18 Sub-menu ..................................... 18 Technical data ........................ 19 Guarantee .............................. 20 TABLE OF CONTENTS 13 ENGLISH NOTES / ACCESSORIES FITTING/REMOVAL Important notes This device is not intended for fitting in the forward section of the passenger compartment where it could also be seen by the driver. Fitting this device in any part of the vehicle where it could interfere with or distract the driver’s attention is dangerous and is not permitted. The manufacturer cannot accept responsibility for any damage caused as a result of improper fitting of this device. To avoid the risk of electrical shock, the device must be protected from water and moisture, and must not be opened. Dangerously high voltages are generated inside the device. We wish to point out that the right to claim against warranty is invalidated by any changes or modifications to the device that have not been explicitly approved by the manufacturer. Accessories supplied Connecting cable Extraction tool Operating instructions Fitting Note It is recommended that the fitting is carried out at a specialist workshop. Prepare the working area . Remove the headrest, and place it on a working surface that has been cleared and cleaned, where the further assembly procedures may be carried out. Note: Take appropriate action to ensure that the headrest is not damaged while fitting the monitor. DANSK 15 ENGLISH DEUTSCH FRANCAIS ITALIANO NEDERLANDS SVENSKA ESPANOL PORTUGUES FITTING/REMOVAL Mark out the dimensions . Feel the covering of the headrest carefully to ensure that there are no invisible parts that would prevent the monitor from being fitted. Use the cardboard template provided to mark out the area that will need to be cut. Carefully cut open the headrest cover Use a knife with an adjustable cutting depth to cut out the planned area. . Make the first cut inside the marked area at a point about 0.5 cm from one of the corners, then make a diagonal cut to a point about 0.5 cm from the opposite corner. . Make a similar cut between the other two diagonally opposed corners. Open the headrest and remove filling and other items . Carefully lift the covering material away from the cut area. . Adjust the cutting depth of the knife to about 2.5 cm, and cut into the headrest following a line about 0.5 cm inside the marked edge. . Carefully lift the filling material at one corner, and cut deeper into the material with the knife. . Remove the filling material in small pieces. . As you do this, lift one piece of the filling material, and ensure that the cut is being made to an even depth. To remove other pieces, use a Dremel saw or another suitable tool. 16 FITTING/REMOVAL . Insert the monitor to check that it will fit into the cut area, and make adjustments if necessary. Lay the cable through the headrest . Now pass the supplied cables through the opening so that they emerge from the underneath of the headrest. . If possible, cover the cable with a cable tunnel. . Now connect the power supply, ground and video signal cables, to check that the monitor is working. Insert the mounting frame in the headrest . Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. . Insert the mounting plate into the area that has been cut out, and fix it in place with appropriate fastenings. Monitor Mounting plate Inserting the monitor . Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. . Insert the monitor into the mounting plate, and attach it with appropriate fastenings. FITTING/REMOVAL Check and adjust the monitor then apply the Velcro strips . Connect the monitor, place it temporarily in the cut-out, and place the headrest into position. . Check the various monitor settings such as brightness, headphone function, volume control and so on. . Then attach the Velcro strips to the rear of the monitor, and push the frame onto the headrest. Take care not to press the screen itself, and apply pressure only in the region of the frame. Removal . To remove the screen, insert the extraction tool between the screen and the mounting plate. . Insert the extraction tool at the place where a slot has been provided...
Este manual também é adequado para os modelos :Vídeo Car - IVMS-5601 (396.29 kb)