Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
The battery’s negative terminal must be disconnected for the entire time it takes to install and connect this device. When doing so, observe the vehicle manufacturer’s safety notices (airbags, alarm systems, trip computers, immobilizers). Before drilling any holes, make sure that no installed cables or vehicle components can be damaged. When installing the signal controller, select a location in the vehicle that allows you to attach it firmly into place using screws. The installation location should be such that the signal controller does not get in the way of the driver and cannot endanger the occupants in the event of the vehicle suddenly coming to a halt, for instance, during an emergency stop. The IR remote control should not be installed within the inflation range of air- bags (driver, passenger side, side air- bags) or in any position where it could be struck by the vehicle occupants’ heads or knees. With regard to the installation location and the attachment using an adhesive pad, check and ensure that the holding strength of the installation surface is sufficient and suitable for all situations and safety requirements. Accessories We recommend you use accessories that have been approved by Blaupunkt. ENGLISH 9 SUPPLIED PARTS SWITCHING ON/OFF Supplied parts The signal controller is supplied with all the parts listed below. Please check that the range of parts supplied with your device is complete. If one of the listed parts is missing, please contact your dealer immediately. . Signal controller 7 607 003 552 . Connecting cable . Screws . IR remote control . IR receiver . Operating and installation instructions Switching on/off Switching on the signal controller The signal controller is switched on via the “+12V ignition” switching line by the connected control device. Switching off the signal controller The signal controller is switched off via the “+12V ignition” switching line by the connected control device. IR REMOTE CONTROL IR remote control Functions The supplied remote control is suitable for operating the signal controller and the monitors. You must enter a button combination in order to control a single monitor or all the monitors simultaneously. To do so, you first select the monitor (FRONT/LEFT/RIGHT-OVERHEAD or ALL) and then the function that you require. The selected monitor or monitors remain(s) selected until you press one of the buttons (FRONT/ LEFT/RIGHT-OVERHEAD or ALL) again. IVRC 05 MUTENAVI POWER BOOSTER FRONT AUDIO CH VOL CH ALL RIGHT LEFT OVERHEAD 1459: 87< ; 236 1 POWER On/off button for the selected monitor or monitors. 2 NAVI Button has no function. 3 VOL • arrow button Increase the volume for the selected monitor (not Audio OUT). VOL • arrow button Decrease the volume for the selected monitor (not Audio OUT). 4 MUTE Mute the volume for all the connected monitors and Audio OUT. 5 CH • arrow button / Select the input source for the selected monitor. 6 RIGHT Select the RIGHT / OVERHEAD monitor. 7 OVERHEAD Select the RIGHT / OVERHEAD monitor. 8 ALL Select all monitors. 9 LEFT Select the left monitor. : FRONT Select the front monitor. ENGLISH 11 IR REMOTE CONTROL INSTALLATION Settings for Audio OUT ; AUDIO CH • Arrow button / Select the input source for Audio OUT. Note: The volume of the input source must be adjustable. < BOOSTER Setting the amplification for Audio OUT / 0 dB or 10 dB. Installation Installation and safety notices Before connecting your signal controller, please read the following information carefully. The battery’s negative terminal must be disconnected for the entire time it takes to install and connect this device. When doing so, observe the vehicle manufacturer’s safety notices (airbags, alarm systems, trip computers, immobilizers). Before drilling any holes, make sure that no installed cables or vehicle components can be damaged. When installing the signal controller, select a location in the vehicle that allows you to attach it firmly into place using screws. The installation location should be such that the signal controller does not get in the way of the driver and cannot endanger the occupants in the event of the vehicle suddenly coming to a halt, for instance, during an emergency stop. The IR remote control should not be installed within the inflation range of air- bags (driver, passenger side, side air- bags) or in any position where it could be struck by the vehicle occupants’ heads or knees. With regard to the installation location and the attachment using an adhesive pad, check and ensure that the holding strength of the installation surface is sufficient and suitable for all situations and safety requirements. INSTALLATION Note: • If the installation requires holes to be Before connecting the monitors to your signal controller, check that the +/- and switching positive connections are working properly. Positive connection Connect the fuse holder (1A fuse) to protect the positive cable (permanent (1), see Fig. 1). The fuse holder should be connecte...