Press the [ 2 ] or [ 3 ] button, the mode switches as follows: [AUTO 1]: Auto Seek Mode FUNCTION TV BAND TV2 SEEK MODE AUTO1 MANUAUTO1 AUTO2 3 3 5 5 . [AUTO 2]: Preset Station Seek Mode 5 . [MANU]: Manual Seek Mode Channel Preset Memory [USER PRESET MEMORY] Store the channel of the station currently being looked to. 1 Press the [ 2 ] or [ 3 ] button to select the [ P1 ] - [ P8 ]. 2 Press the SCRN button for at least two seconds to store the channel of the station currently. FUNCTION USER PRESET MEMORY P1 2 34P4 6P2 3 P3 4 P6 9P5 7 P7 10 P8 12 3 3 5 NOTE You can store 8 stations in each of the TV1 and TV2 preset bands. Selecting the Reception Area [TV AREA] Press the [ 2 ] or [ 3 ] button to select the channel setting for your country as follows: 1 China PAL-D 2 Singapore Malaysia Thailand Brunei PAL-B/G 3 Hong Kong PAL-I 4 Indonesia PAL-B/G 5 Australia FUNCTION TV AREA TV1 2 4 5 China1 3 3 3 NOTE The reception area can be set for two separate preset bands, TV1 and TV2. Operation English 7.0-inch WIDE COLOR LCD MONITOR MODE V.SEL SCRN Setting the Remote Sensor On/Off [REMOTE] If this unit also runs when operating other units with different Kenwood remote controls, its remote control function can be turned off. Press the [ 2 ] or [ 3 ] button to switch the function on and off. FM Transmitter Function [FM-TX] You can use the FM transmitter function to hear the sound of the TV, video from your car FM radio. Press the [ 2 ] or [ 3 ] button to change the frequency by 0.1 MHz step and off [OFF]. NOTE • *The KTC-V800N is not display the FM transmitter function depending on the sales area. FUNCTION REMOTE OFF FM-TX 87.5MHz AV-OUT NORMAL 87.5 3 3 FUNCTION REMOTE OFF FM-TX 87.5MHz AV-OUT NORMAL OFFON 3 3 • Be sure to select a frequency that is not the same as a broadcast station in your area. • The auto seek function on your car radio may not stop at the FM transmitter frequency. In this case, use the manual seek function to set the radio to the FM transmitter frequency. Switching the AV Output [AV-OUT] Press the [ 2 ] or [ 3 ] button, the AV output mode switches as follows: Ў [NORMAL](NOR): Picture/sound with monitor picture Ў [TV]: Television picture/sound Ў [VIDEO1](VD1): Video 1 picture/sound Ў [VIDEO2](VD2): Video 2 picture/sound FUNCTION REMOTE OFF FM-TX 87.5MHz AV-OUT VIDEO1 VD1NOR TV VD2 3 3 8 Remote Control Function Remote Control Function Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries 1. Use two "AA" batteries: Slide the cover while pressing downwards to remove it as illustrated. 2. Insert the batteries with the . and · poles aligned properly following the illustration inside the case. Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. •The provided batteries are intended for use in operation checking, and their service life may be short. • When the remote controllable distance becomes short, replace both of the batteries with new ones. NOTE 2WARNING 2CAUTION REMOTE CONTROL UNIT RC-210 AME SP SEEK MODE V.SEL CH. – CH. + AV OUT VOL 5 . SEARCH M/S BAND 4 . Monitor Control Function •V.SEL button Each time you press V.SEL button to switch the monitor's picture. • MODE button Each time you press MODE button to switch the screen mode. •AV OUT button Each time you press AV OUT button to switch the AV output mode. TV Control Function • BAND button Each time you press the BAND button, the preset band switches between the TV1 and TV2. • SEARCH buttons Press the ./CH.+ button to make increasing seeks. Press the 4/CH.– button to make decreasing seeks. • SEEK button Each time you press the SEEK button, the seek mode switches to auto 1, to auto 2 and to manual. • AME button You can automatically store all the receivable channels in the band currently being looked to. 1 Select the band for auto memory entry. 2 Press the AME button. 3 Press the ./CH.+ button to start auto memory entry. English English n Accessories External view External view ......... Number of items ......... Number of items 1 4 ........1 ........5 (O4 x 12 mm) 2 5 ........1 ........2 (O4 x 16 mm) 3 ........1 Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wiring harness wires in the following order: ground, ignition. 4. Connect the wiring harness connector to the unit. 5. Install the unit in your car. 6. Reconnect the · terminal of the battery. 7. Press the reset button. (See p. 3) 2WARNING •This product is intended for use with 12V DC negative ground power only. Do not connect it to any other power supply •To prevent shorting, disconnect the battery wire from the negative terminal of the batt...
