Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
. The alarm will only sound if the built-in amplifier is used. Notes (.-B) . You cannot use multiple auxiliary devices simultaneously, even if they are connected to different terminals. . To connect an iPod via RC-202IPV, make sure to connect the video output plug to AUX1 IN. Connection diagram . To a common ground (earth) point First connect the black ground (earth) lead, then connect the yellow and red power supply leads. . To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster Notes . It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). . If your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. . To a car’s illumination signal Be sure to first connect the black ground (earth) lead to a common ground (earth) point. . To the +12 V power terminal which is energized when the ignition switch is set to the accessory position Notes . If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to first connect the black ground (earth) lead to a common ground (earth) point. . If your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” . To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth) lead to a common ground (earth) point. . To the parking brake switch cord . To an auxiliary device such as a portable media player, game console, etc. (not supplied) Tip You can use an RCA cord (not supplied) to connect auxiliary devices. . To the +12 V power terminal of the car’s rear lamp lead (only when connecting the rear view camera) Notes on the control and power supply leads . REM OUT lead (blue/white striped) supplies +12 V DC when you turn on the tuner. . If your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect REM OUT lead (blue/white striped) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. . A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. *1 Speaker impedance: 4 – 8 ohms . 4 *2 For details on installing the microphone, see “Installing the microphone (.)” on the reverse side. *3 Whether in use or not, route the microphone input cord such that it does not interfere with driving. Secure the cord with a clamp, etc., if it is installed around your feet. *4 RCA pin cord (not supplied) *5 For details on connecting to the parking brake switch cord, see “Connecting the parking brake lead (.)” on the reverse side. *6 The sound is output from this terminal only when ZONE x ZONE is activated. This terminal outputs a fixed level regardless of the volume control of the unit. *7 A separate adaptor may be required. *8 Not supplied. Cautions . Run all ground (earth) leads to a common ground (earth) point. . This unit is designed for negative ground (earth) 12 V DC operation only. . Do not disassemble or modify the unit. . Do not install in locations which interfere with airbag operation. . Do not get the leads under a screw, or caught in moving parts (e.g. seat railing). . Before making connections, turn the car ignition off to avoid short circuits. . Connect the yellow and red power supply leads only after all other leads have been connected. . Be sure to insulate any loose unconnected leads with electrical tape for safety. . Do not press on the LCD when installing the unit. . Install the unit with the monitor facing straight forward; do not install it at a slanted angle. Notes on the power supply lead (yellow) . When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component's fuse amperage rating. . If no car circuits are rated high enough, connect the unit directly to the battery. Parts list . The numbers in the list correspond to those in the instructions. . The bracket . is attached to the unit before shipping. Before mounting the unit, use the release keys . to remove the bracket . from the unit. For details, see “Removing the bracket (.)” on the reverse side of the sheet. . Keep the release keys . for future use as they are also necessary if you remove the unit from your car. . Assemble the parts of the microphone . before use. For details, see “Installing the microphone (.)” on the reverse side. Caution Handle the bracket . carefully to avoid injuring your fingers. ...