Log:
Assessments - 1, GPA: 5 ( )

Instruções de Operação Sony, Modelo SA-VE2M

Fabricante : Sony
Arquivo Tamanho: 117.44 kb
Arquivo Nome : 4246771111.pdf
Língua de Ensino: itenfrde
Ir para baixar



por este dispositivo também tem outras instruções :
Speakers - SA-VE2M (62.7 kb)en
Speakers - SA-VE2M (136.27 kb)ruptdafi
Speakers - SA-VE2M (126.75 kb)plsvesnl

Facilidade de uso


On cleaning Clean the speaker cabinets with a soft cloth lightly moistened with a mild detergent solution or water. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. The volume level should not be turned up to the point of distortion. If the volume level is too high, the speaker protection circuit activates, and the sound level drops suddenly. This is not a malfunction. In this case, lower the volume level and wait for a few moments until the unit resumes normal operation. If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer. Hooking up the system Connect the speaker system to the speaker output terminals of an amplifier. (A) Make sure power to all components (included the subwoofer) is turned off before starting the hook-up. Notes (B) • Make sure the plus (+) and the minus (–) terminals on the speakers are matched to the corresponding plus (+) and minus (–) terminals on the amplifier. • Be sure to tighten the screws of the speaker terminals securely as loose screws may become a source of noise. • Make sure all connections are firm. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. • Do not connect the subwoofer to the amplifier’s CENTER output terminal (which is for Dolby Pro Logic or Dolby Digital). No bass sound will output from the subwoofer if you do. • For details regarding the connections on the amplifier side, refer to the manual that was provided with your amplifier. Tip All striped wires are minus (–) in polarity, and should be connected to the minus (–) speaker terminals. . 2003 Sony Corporation Printed in Malaysia AEeBFront (Right) Avant (droite) Center Centre Subwoofer Caisson de grave Front (Left) Avant (gauche) CAABBCenter Centre Subwoofer Caisson de grave Surround (Right) Surround (droite) Front (Left) Avant (gauche) Surround (Left) Surround (gauche) DFront (Right) Avant (droite)3.5 m 3,5 m EeEeEe 10 m Surround (droite) Surround (gauche) eEEeEeEeEeEeEeEeR INPUT WOOFER OUT FRONT CENTER REAR R L L Surround (Right) Surround (Left) Amplifier Amplificateur 3.5 m 3,5 m 10 m 3.5 m 3,5 m E F Foot pads Tampons autocollants WS-WV10D (for surround speakers) (pour les haut-parleurs WS-FV10D surround) Positioning the speakers Location of each speaker (C) Each speaker should face the listening position. Better surround effect will result if all speakers are set at the same distance from the listening position. Place the front speakers at a suitable distance to the left and right of the television. Place the subwoofer on either side of the television. Place the center speaker on the top-center of the TV set. The placement of surround speakers greatly depends on the configuration of the room. The surround speakers may be placed on both sides of the listening position A or behind the listening position B. Tips • Movies are best enjoyed in a room that produces no echoes (as in one with surrounding curtains). • Music (especially classical music) is best enjoyed in a room that produces some echo. Setting the speakers Attaching the speaker pads (D) To prevent speaker vibration or movement while listening, attach the supplied foot pads to the bottom four corners of the center speaker, front speakers, and surround speakers. Setting the center speaker (E) Set the center speaker firmly on top of the TV set. Make sure it is completely level. Setting other speakers (F) For greater flexibility in the positioning of the speakers, use the optional WS-FV10D or WS-WV10D speaker stand (available only in certain countries). Tip (G) The height of the front speakers should be adjusted to about the center of the TV screen. Setting the amplifier When connecting to an amplifier with internal multi channel decoders (Dolby Digital, DTS**, etc.), you should use the setup menus for the amplifier to specify the parameters of your speaker system. See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. Speaker setup For Set to Front speakers SMALL Center speaker SMALL Surround speakers SMALL Subwoofer ON (or YES) If you use the amplifier with adjustable crossover frequency, it is recommended to select 120 Hz (or close to this figure) as the crossover frequency for your front, center, and surround speakers. ** “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Listening to the sound (H) First, turn down the volume on the amplifier. The volume should be set to minimum before you start playing the program source. 1 Turn on the amplifier and select the program source. 2 Press POWER on the subwoofer. The POWER indicator on the subwoofer lights up green. 3 Play the program source. Adjusting the subwoofer (H) Rotate LEVEL to adjust the volume. Set the volume level to best suit your preference according to the program source. Notes • Some amplifier functions for enhancing the sound may ...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias