Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Keep these instructions. Retain this booklet for future reference. Please read the following safety instructions carefully. 1. This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following procedures for installation, use and servicing. This unit doesn’t contain any parts that can be repaired by the user. 2. The screen display is operated automatically. Do not draw the screen display out or turn it upward or downward manually. Otherwise, the mechanism construction may be harmed to some degree. 3. When you operate the display unit, do not touch the display by your hands. It may harm your fingers. 3 INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop. • If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. 30° • Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. INSTALLATION HARDWARE Tapping Screw (M5 x 25) (1 pcs) Nut (M5) (1 pcs) Mounting Bolt (M5 x 5) (8 pcs) Strap (1 pcs) Double Sided Tape (2 pcs) Hexagonal Bolt (M6 x 12) (4 pcs) Plain Washer (M5) (1 pcs) Lever (2 pcs) Tapping Screw (M5 x 12) (4 pcs) Spring Washer (M5) (5 pcs) Bracket (A) Bracket (B) Spring Washer (2 pcs) (2 pcs) (M6) (4 pcs) 4 INSTALLATION MOUNTING THE TUNER UNIT Step 1 Step 2 1 1 2 6 4 5 7 3 8 6 4 6 5 7 8 5 7 3 1. Bracket (A) 2. Mounting Bolt (M5 x 5) 3. Bracket (B) 4. Hexagonal Bolt with Washer (M6 x 12) 5. Tapping Screw with Washer (M5 x 12) 6. Spring Washer (M6) 7. Spring Washer (M5) 8. Double Sided Tape INSTALL THE DISPLAY UNIT Before install the display unit, please remove its tail screw and cable parts. This unit can be properly installed either from “front” (convertional DIN Front- mount) or “rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. DIN FRONT-MOUNT Installing the unit 1 3253 (Fig. 1) 1. Dashboard 2. Holder After inserting the holder into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place. 3. Display Unit (Fig. 2) 7 5436 1 2 1. Dashboard 2. Nut (M5) 3. Spring Washer 4. Tapping Screw with Washer (M5 x 25) 5. Screw 6. Plain Washer 7. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 5 INSTALLATION Removing the unit 1 1. Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers upward and out to makes it possible to remove the unit. DIN REAR-MOUNT Installation using the screw holes on the both sides of the unit. 1 2 3 5 2 5 4 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 x 5mm), depending on the shape of the screw holes in the bracket. 2. Screw 3. Factory Radio Mounting Bracket 4. Dashboard or Console 5. Hook and Screw (Remove this part) Note: The frame, strap, and half-sleeve are not used for REAR-MOUNT. Fastening the unit to the factory radio mounting bracket. 6 CAUTION: 1. If the TV control grey cable is connected to car brake, when the car is running, you cannot switch into TV mode, and the button (2) or (OPEN/CLOSE) button (31) is unavailable. 2. To select CD changer’s sort: Before installing the unit, connect the CD changer with the unit correctly and turn on the power to make the unit work in CD changer state. If the operation normally, the switch button’s position is right, otherwise, please dial the switch button to the other position. Note: How to select A or B in CDC SET is different according to the units of the customers use. 7 ELECTRICAL CONNECTION RADIO/TV MAIN UNIT (VIEW FROM REAR) TV DIVERSITY ANTENNA INPUT CDC INPUT GREY TV CONTROL GREY/BLACK TV DIVERSITY ANTENNA INPUT RADIO ANTENNA INPUT TO CD CHANGER BLUE/WHITE POWANT REAR Rch SPK VIOLET VIOLET/BLACK FRONT Rch SPK GREY GREY/BLACK REAR Lch SPK GREEN GREEN/BLACK FRONT Lch ...