Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
After the new message is played, the PLAY/ SKIP indicator lights. SCREENING CALLS To screen calls, let the TAD-1027 answer them, then listen to the caller’s message through the TAD’s speaker. If you decide to answer the call, pick up any phone on the same phone line as the TAD. The TAD stops recording and resets to answer the next call. Note: If you pick up the phone just as the TAD-1027 answers, the TAD might not stop playing the outgoing message. If this happens, press ANSWER/STOP/DELETE to stop the TAD. If you do not want to take the call, do not pick up the handset, and let the TAD1027 finish recording the caller’s message. 43-787.fm Page 11 Monday, August 16, 1999 8:11 AM PLAYING MESSAGES If there are new messages, the PLAY/ SKIP indicator flashes until all the new messages have been played. To play all the messages, press PLAY/ SKIP. The TAD-1027 announces the number of messages or if there are no messages stored, the TAD announces, “No message.” Illus. showingPLAY/SKIP. Before playing each message, the TAD1027 announces the message number and the day and time when the message was recorded. After all messages play, the TAD announces, “End of message( s)” then it resets to answer calls. Repeating Messages To replay a message, if you have listened to at least 5 seconds of it, press OGM/REPEAT. The current message starts again. If you have not listened to 5 seconds of the message, or the message is not at least 5 seconds long, pressing OGM/REPEAT replays the previous message. Skipping Messages To skip to the next message during playback, press PLAY/SKIP once. The next recorded message plays. Pausing Message Playback To pause message playback, press ANSWER/ STOP/DELETE. To resume playing messages, press PLAY/SKIP. Otherwise, after pausing for 60 seconds, the TAD1027 sounds three beeps and stops playback. Stopping Message Playback To stop playback at any time, press ANSWER/ STOP/DELETE twice. The TAD1027 beeps once and resets to answer calls. DELETING MESSAGES To delete all the messages you have already listened to, while playback is stopped, hold down ANSWER/STOP/DELETE. The TAD-1027 sounds a long beep then deletes all old messages, but keeps PLAY/ ing). anySKIP new messages indicator continu(and the es flash11 43-787.fm Page 12 Monday, August 16, 1999 8:11 AM Notes: • If you have played only a portion of a message, the TAD-1027 might not delete it. • Individual messages can only be deleted by remote operation. RECORDING A MEMO A memo is a message you can record at the TAD-1027 without having to call in on a phone. Notes: • The maximum memo length is 60 seconds. • When memory is full, the TAD-1027 announces, “Memory is full,” and you cannot record the memo. Delete old messages to make room in memory (see “Deleting Messages” on Page 11). Follow these steps to record a memo. 1. Hold down PLAY/SKIP until the TAD1027 beeps. 2. Speak in a normal voice into the microphone on the front of the TAD. 3. The TAD-1027 automatically stops recording after 60 seconds, or you can press ANSWER/STOP/DELETE when you finish the memo. The TAD-1027 beeps once. 12 The memo is recorded along with the incoming messages. To hear the memo, simply play back your messages. CHANGING THE REMOTE OPERATION SECURITY CODE The TAD’s remote operation security code is preset to 787. You can operate your TAD-1027 remotely with this code; however, we recommend that you set your own code. Notes: • Be sure to set each digit within 8 seconds. Otherwise, you must start over from Step 1. • If the AC power fails or if the backup battery becomes weak, the remote operation security code automatically resets to 787. 1. Use a pointed object, such as a straightened paper clip, to hold down CODE until the TAD-1027 beeps and announces the first digit of the current security code. Illus. showing CODE switch. 43-787.fm Page 13 Monday, August 16, 1999 8:11 AM 2. Repeatedly press PLAY/SKIP or OGM/REPEAT to set the first digit, then press ANSWER/STOP/DELETE. The TAD-1027 beeps and announces the second digit. 3. Repeatedly press PLAY/SKIP or OGM/REPEAT to set the second digit, then press ANSWER/STOP/ DELETE. The TAD-1027 beeps and announces the third digit. 4. Repeatedly press PLAY/SKIP or OGM/REPEAT to set the third digit, then press ANSWER/STOP/DELETE. The TAD-1027 beeps once and announces the complete remote operation security code. 13 43-787.fm Page 14 Monday, August 16, 1999 8:11 AM REMOTE OPERATION You can operate the TAD-1027 from almost any touch-tone phone, or from a rotary phone using a pocket tone-dialer (available at your local RadioShack store). Notes: • When the memory is full, the TAD1027 answers the call after two rings and announces, “Memory is full.” Delete some of the old messages to make room in memory (see “Using Remote Commands”). • If the ring select switch is set to TS (toll saver), the TAD-1027 answers after two rings if you have new messages (ones you have not played). If there are no new messages, the TAD waits for four rings before it ...