Assessments - , GPA:
(
)
)
Fabricante : Radio Shack
Arquivo Tamanho: 378.04 kb
Arquivo Nome : 4300786_PM_EN.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
DC 9V Jack illustration When you first connect power, the TAD beeps once and the message counter counts up from 0 to 10. Then the TAD beeps. A1, A2, Lo, CL and 0 alternately appear to indicate that no outgoing messages are recorded, and the day/time stamp is not set. 43-786.fm Page 9 Monday, August 16, 1999 8:02 AM On a Wall Plate 1. Plug one end of the supplied short modular cord into the TEL. LINE jack on the top of the TAD. 2. Route the cord into the groove on the phone’s base. 3. Position the phone’s base close to the wall plate and plug the other end of the short modular cord into the wall plate jack. 4. Align the wall plate studs with the TAD’s keyhole slots and slide the TAD downward to secure it. 5. Plug one end of the supplied coiled cord into the jack on the left side of the TAD-1026. Plug the other end into the handset’s jack. 6. Insert the supplied adapter’s barrel plug into the DC 9V jack on the top of the TAD. Then plug the adapter’s other end into a standard AC outlet. DC 9V Jack illustration When you first connect power, the TAD beeps once and the message counter counts up from 0 to 10. Then the TAD beeps. A1, A2, CL and 0 alternately appear to indicate that no outgoing messages are recorded, and the day/time stamp is not set. 7. Slide the handset clip up and out of its retaining slot, rotate it 180°, then slide the clip back into its slot. Place the handset on the TAD. 7.epsi 9 43-786.fm Page 10 Monday, August 16, 1999 8:02 AM Directly on a Wall For this mounting method, you need two flat-head wood screws (not supplied) with heads that fit into the keyhole slots on the bottom of the TAD. 1. Drill two holes 315/16 3/16 inches (100 mm) apart. Then thread a screw (not supplied) into each hole letting 315/16 the heads extend about 3/16 of an inch (5mm) from the wall. 2. Plug one end of the supplied long modular cord into the TEL. LINE jack on the top of the TAD. 3. Plug the cord’s other end into a modular phone line jack. 4. Align the two screws with the keyhole slots on the bottom of the TAD. Slide the TAD down onto the screws to secure the TAD to the wall. 5. Plug one end of the supplied coiled cord into the jack on the left side of the TAD-1026. Plug the other end into the handset’s jack. 6. Insert the supplied adapter’s barrel plug into the DC 9V jack on the top of the TAD. Then plug the adapter’s other end into a standard AC outlet. 10 When you first connect power, the TAD beeps once and the message counter counts up from 0 to 10. Then the TAD beeps. A1, A2, CL and 0 alternately appear to indicate that no outgoing messages are recorded, and the day/time stamp is not set. 7. Slide the handset clip up and out of its retaining slot, rotate it 180°, then slide the clip back into its slot. Hang the handset on the base. 7.epsi SETTING THE DIALING MODE Set T/P (tone/pulse) on the top of the TAD-1026 for the type of service you have. If you are not sure which type you have, do this test. 43-786.fm Page 11 Monday, August 16, 1999 8:02 AM 1. Set T/P to T. 11.epsi 2. Lift the handset and listen for a dial tone. 3. Press any number other than 0. Note: If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not press the access code either. If the dial tone stops, you have touch-tone service. Leave T/P set to T. If the dial tone continues, you have pulse service. Set T/P to P. SETTING THE DAY AND TIME The answering system records the day and time of the call with each phone message. Follow these steps to set the current day and time. Notes: • To avoid having to reset the time if AC power is lost, we recommend you install a backup battery before you set the day and time. See “Installing the Backup Battery” on Page 7. • If you do not complete each step within 8 seconds, the TAD stops setting and announces the day and time. Start again from Step 1. 1. Hold down STOP/T-SET untilTAD announces, “Sunday.” (clock) then 01 appear. 13.epsi the CL Note: Adjust VOLUME on the right side of the TAD to the desired listening level. illustration 11 43-786.fm Page 12 Monday, August 16, 1999 8:02 AM 2. To change the day of the week, repeatedly press MEMO to move backward or CODE to move forward until the TAD announces the desired day of the week. 3. Press STOP/T-SET. The TAD announces the hour. 4. To change the hour, repeatedly press MEMO to move backward or CODE to move forward to the desired hour. 5. Press STOP/T-SET. The TAD announces the minute. 6. To change the minutes, hold down MEMO to move backward or CODE to move forward to the desired minute. 7. Press STOP/T-SET to confirm the settings. The TAD announces the day and time and CL disappears. To check the current day/time at any time, press STOP/T-SET. 12 SETTING THE RINGER’S VOLUME To adjust the ringer’s volume, set OFF.LO.HI to HI for a noisy room (such as a kitchen), or LO for a quiet room (such as a bedroom). If you do not want to be disturbed by a ringing phone, set the switch to OFF. The telephone doe...