Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
The answering system saves all information, including the outgoing message, on tape so it will be saved during a power failure. When power is restored after a power failure, the answering system plays the tape automatically to restore the outgoing message to the digital chip. Checking the Outgoing Message Press OGM REC/PLAY at any time to hear the outgoing message. The answering system beeps once and plays back the message, then beeps twice. To adjust the volume, see “Setting the System’s Volume” on Page 13. 7 43-785.fm Page 8 Monday, August 16, 1999 7:54 AM PLACING THE PHONE ON A DESKTOP To use your answering system on a desk, table, or shelf, plug one end of the supplied telephone cord into PHONE JACK and plug the other end into a modular phone jack, then proceed to “Connecting the Handset” on Page 10. Illust. MOUNTING THE PHONE Using the supplied mounting bracket, you can mount the TAD-285 on a phone jack wall plate or directly on the wall. On a Wall Plate 1. Plug one end of the supplied modular cord into PHONE JACK. Illust. 8 2. Align the adapter’s power cord with the left slot on the top and bottom of the mounting bracket. Align the modular cord with the right slot on the top of the mounting bracket. Pull the other end of the modular cord through the large hole in the center of the bracket. 3. Insert the mounting bracket’s tabs into the slots on the bottom of the answering system. Then pull the bracket up until it snaps into place. Illust. 4. Coil all the excess modular cord into the recess of the mounting bracket by pushing it back through the large hole. Leave only about 1–2 inches of the cord outside the bracket. 43-785.fm Page 9 Monday, August 16, 1999 7:54 AM 5. Plug the exposed end of the cord into a modular phone jack wall plate. Illust. 6. Line up the keyhole slots on the bracket with the studs on the wall plate, then slide the bracket down onto the wall plate until it is secure. 7. Pull the handset holder toward you as far as it will go. Hold it out as you rotate the holder 180°, then let it snap back in place. Illust. The holder’s tab helps hold the handset in the cradle while the answering system is mounted on the wall. 8. Proceed to “Connecting the Handset” on Page 10. Directly on the Wall Using a drill and screws (not supplied) and the supplied mounting bracket, you can easily mount your TAD-285 directly on the wall. 1. At the desired mounting location, drill two holes 31/4 inches apart, one above the other. Illust. 2. Thread a screw into each hole until the screw’s head extends about 1/8 inch from the wall. Illust. 3. Plug one end of the supplied modular cord into PHONE JACK. Illust. 9 43-785.fm Page 10 Monday, August 16, 1999 7:54 AM 4. Align the adapter’s power cord with the left slot on the top and bottom of the mounting bracket. Align the modular cord with the right slot on the top and bottom of the mounting bracket. 5. Insert the mounting bracket’s tabs into the slots on the bottom of the answering system. Then pull the bracket up until it snaps into place. Illust. 6. Plug the modular cord into a modular phone jack. 7. Line up the keyhole slots on the bracket with the screws on the wall, then slide the bracket down onto the screws until it is secure. Illust. 10 8. Pull the handset holder toward you as far as it will go. Hold it out as you rotate the holder 180°, then let it snap back in place. Illust. The holder’s tab helps hold the handset in the cradle while the answering system is mounted on the wall. 9. Proceed to “Connecting the Handset” on Page 10. CONNECTING THE HANDSET Plug one end of the coiled handset cord into the answering system’s handset jack. Plug the other end into the jack on the handset. Place the handset on the cradle. Illust. 43-785.fm Page 11 Monday, August 16, 1999 7:54 AM SETTING THE RINGER SWITCH To set the volume of the telephone’s ringer, set the ringer switch on the back of the answering system to LO or HI. To turn off the telephone’s ringer, set the ringer switch to OFF. You can still make out-going calls. If you hear an extension phone ring, you can still answer calls. Illust. SETTING THE DIALING MODE Set P/T for the type of service you have — P for pulse (rotary) or T for tone. If you are not sure which type you have, do this test once you connect the phone to power. 1. Set P/T to T. Illust. 2. Pick up the handset and listen for a dial tone. 3. Press any number other than 0. If the dial tone stops, you have touch-tone service. If the dial tone continues, you have pulse service. Set P/T to P. Notes: •The # button does not function when P/T is set to P. • If you have pulse service and want to use a special service that requires tone signals (such as bank-by-phone), see “Using Tone Services with a Pulse Line” on Page 15. 11 43-785.fm Page 12 Monday, August 16, 1999 7:54 AM ANSWERING SYSTEM OPERATION SETTING THE ANSWERING SYSTEM TO ANSWER CALLS Rotate VOLUME toward HI until it clicks. When the red light on the PLAY button stays on without the answering syste...