Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
IMPORTANT: In order to use this unit, you must subscribe to either the standard Name/Number Caller ID Service or Caller ID with Call Waiting Service. To know who is calling while you are on the phone, you must subscribe to Caller ID with Call Waiting Service. Base Layout Connections and Setup Play/Stop button New Call indicator Menu button 3/DIR (directory button) Sel/Save button Memo/Record button Format button Exit button Dial button Delete button 5/6 (volume +/- buttons) 4/CID (Caller ID button) DND (Do Not Disturb button) Auto Redial button Answer L1/L2 buttons Flash button Store button Hold button Confer (conference button) Line 1/2 buttons Microphone Preset EQ button Mute button Headset button Speaker button # PAUSE button 16 One Touch Dial buttons Parts Checklist Make sure your package includes the following items: Telephone Jack Requirements To use this phone, you will need one RJ14C two-line jack or two RJ11C single line jacks, which might look like the one pictured here, installed in your home/ office. Installation Important Installation Information • Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Connections and Setup Desktop Pedestal AC power adaptor Base Handset cord Line cords Handset Wall plate Modular telephone line jack Installing the Phone 1. Choose an area near an electrical outlet and telephone wall jack. Your phone should be placed on a level surface, such as a table top or desk. 2. Install 4 AAA-size alkaline batteries (not included) for back up power in the event of a power failure. CAUTION: Unit will not work if electrical power fails and batteries are depleted or not installed. Therefore it is important that you replace them when “REPLACE BATTERY” shows in display in order to maintain unit operation. As a precaution, you may want to write down any stored information you do not want erased. • Open the battery compartment door located on the bottom of the phone by inserting a flathead screw driver into the battery door latch area and gently tilting the screw driver away from the battery door to release the latch. • Insert the batteries as shown on the diagram inside the battery compartment. • Snap the battery compartment door back into place. IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they can leak and damage the unit. 3. Connect the AC power adaptor to an electrical outlet and the DC connector to the back of the base. CAUTION: To reduce risk of personal injury, fire, or damage use only the 5-2719 power adaptor listed in the user’s guide. This power adaptor is intended to be correctly orientated in a vertical or floor mount position. Connections and Setup 4. Attaching the Desktop Pedestal: A. Turn the phone over so that the bottom of the base is facing up and the end with data port and line jacks is pointing away from you. B. Turn the desktop pedestal so that the side with four rectangle rubber feet is facing you. C. Insert the tabs on the pedestal into the two lower slots on the bottom of the base, then push the pedestal downward until the tabs on the top of the pedestal snap (lock) into place. 5. Connect the telephone line cords: Connections and Setup 6 4 3 5 If you have two telephone lines installed on a single jack, plug one end of the straight telephone line cord into the jack marked LINE 1+2 on the back of the base. Plug the other end into the 2-line wall jack. If you have two separate telephone line jacks, plug one telephone line cord into the jack marked LINE 1+2 and another cord into the jack marked LINE 2. Plug the other end of each line cord into separate wall jacks. NOTE: To use two lines, you must have two telephone lines with unique telephone numbers. If you only have one telephone line, this phone will still operate, but only as a single line telephone. 6. Connect the handset cord: Plug one end of the coiled handset cord into the side of the base and the other end into the jack on the handset, and place the handset in the cradle. 7. Check for a dial tone. Lift the handset and listen for a dial tone. If you hear a dial tone, the phone is properly installed. Data Port This phone has a DATA PORT jack to connect an auxiliary phone device, such as a fax machine, computer modem, answering system, or even a cordless phone. The DATA PORT switch on the back of the phone controls the DATA PORT jack so you can choose line 1 or line 2. Connections and Setup Use the DATA PORT jack to hook up your fax machine, for example, and then set the DATA PORT switch to 2 in order to receive faxes on the phone number for line 2. If you are talking to someone on line 2 and want them to fax something to you, change the DATA PORT swi...