Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
51 3 English EN Contents 1 Important 4 Safety 4 Notice 4 2 Your car power amplifier 5 Introduction 5 What’s in the box 5 Overview of the main unit 5 3 Installation 6 Mount the amplifier in car 6 Connect speakers 7 Connect car audio 7 Connect power 7 4 Use your power amplifier 9 Select filter mode 9 Select LPF frequency 9 Adjust input level 9 Adjust bass boost 9 About the protector indicator 9 Replace fuse 10 5 Product information 10 6 Troubleshooting 11 4 Notice Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. 1 Important Safety Read and understand a • ll instructions before you use the apparatus. If damage is caused by failure to follow instructions, the warranty does not apply. • This unit is designed for negative ground (earth) 12 V DC operation only. • Use only the supplied mounting hardware for a safe and secure installation. • Do not connect any active speakers (with built-in amplifier) to the speaker terminals of the unit. Doing so may damage the active speakers. • To ensure safe driving, adjust the volume to a safe and comfortable level. • To avoid short circuit, do not expose the apparatus, remote control or remote control batteries to rain or water. • Never expose the apparatus to direct sunlight, naked flames or heat. • Clean the apparatus with soft, damp cloth. Never use substances such as alcohol, chemicals or household cleaners on the apparatus. EN 5 Overview of the main unit a INPUT L/R Connect c • ar audio with RCA cable. b OUTPUT L/R • To connect additional amplifier with RCA cable for additional speakers. c INPUT LEVEL • Adjust input level (0.3V to 6V). d FILTER MODE • Set frequency filter at LPF (low-passfilter), HPF (high-pass-filter), or OFF (flat) mode. e LPF FREQUENCY • Set LPF (low-pass-filter) frequency from 80Hz to 180Hz. f BASS BOOST • Boost frequency for around 50Hz, 12dB. g POWER/PROTECTED • Light in green when the amplifier is switched on. • Light in red when the amplifier is abnormal and protected. h SPEAKER OUTPUT • Connect to speakers or subwoofers. (30A) 2 Your car power amplifier Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at Introduction With the amplifier, you can enjoy high quality sound performance with powerful bass and beats. What’s in the box Check and identify the contents of your package: a Amplifier b Screw (25mm) x 4 c Fuse x 1 English EN 6 3 Installation Note Follow all mounting a •• nd wiring instructions. Mount the amplifier in car You can mount the amplifier either under a seat or on the rear tray. Note •• To avoid interference, do not place the amplifier too close to the car audio or antenna. •• The supplied mounting screws are 25mm long. Make sure that the mounting board is thicker than 25mm. 1 Place the unit on the location for installation. 2 Mark the positions of the four screw holes. 3 Drill the holes with driller of approximately 4mm in diameter. 4 Mount the unit with the supplied screws. i FUSE: 30AX1 j POWER • To connect +12V-DC power wire, ground wire, and remote control wire. EN 7 Connect car audio Option 1: Line input connection Connect the amplifier to the car audio with an RCA cable (not supplied). Car audio unit LINE OUT Option 2: Line output connection Connect the amplifier to another amplifier. Connect speakers Note Use speakers with an •• impedance of 2 to 8 ohm (4 to 8 ohm when used as a bridged amplifier). •• Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may degrade sound quality. Option 1: Stereo mode: connect 2 speakers 4 ohm speaker 4 ohm speaker (30A) Option 2: Mono bridged mode: connect 1 speaker 4 ohm speaker (30A) Option 3: Tri-mode: connect 3 speakers (30A) 4 ohm speaker 8 ohm speaker 4 ohm speaker English EN 8 Connect power 1 Make the power connection as illustrated below: Connect the g • round wire from the car to the GND socket. • Connect the remote wire from the car audio to the REM socket. • With this connection, you can turn on/off the amplifier with the car audio. • Connect the...
Este manual também é adequado para os modelos :Avtousiliteli - CMQ205 (1.45 mb)