Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Please refer to GMOS-100i for 20 pin connector instructions *Read Important Warning On Page 1 Before Attempting Any Installation* APPLICATIONS GMLAN29-100 BUICK Enclave 2007-10 Lucerne 2006-10 CADILLAC Escalade 2007-10 DTS 2006-10 SRX 2007-09 CHEVROLET Avalanche 2007-10 Equinox 2007-09 Express 2008-10 Impala 2006-2010 Monte Carlo 2006-2007 Silverado (new body) 2007-10 Suburban 2007-09 Tahoe 2007-09 Traverse 2009 GMC Acadia 2007-10 Savanna 2008-10 Sierra (New body) 2007-10 Yukon 2007-10 HUMMER H2 2008-09 PONTIAC Torrent 2007-09 Vibe 2009 SATURN Outlook 2007-09 Vue 2008-09 SUZUKI XL-7 2007-09 INTERFACE COMPONENTS •A) 4 pin harness with stripped leads •B) 22 pin to 30 pin GM harness •C) 16 pin backup camera harness •D) 16 pin RSE harness A B 4 pin C D TOOLS REQUIRED FOR INSTALLATION •Cutting Tool •Tape •Crimping Tool •Connectors (I.E. butt-connectors, bell caps, ECT…) IGNITIONTERMINALS WIRECUTTERM3.5 M2.6 M3 M5 M4 ISO 62.51.5 TABLE OF CONTENTS Installing The Interface .............................................................. 1 Installing The GMLAN29-100 ................................................. 1 Programming SWC ..................................................................... 2 Testing The GMLAN29-100 ...................................................... 2 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians *Important: Before beginning any of the following, disconnect the negative battery terminal to prevent an accidental short circuit. INSTALLING THE INTERFACE From the 22 way harness: • Connect the Black wire with the ring terminal to the back of the aftermarket radios chasis • Connect the 3.5mm jack to your aftermarket radios steering wheel control input (if equipped) From the 30 way harness: • Connect the Black wire to the ground wire of the aftermarket radio • Connect the RCA’s on the 8 pin harness to theAUX in on the aftermarket radio (if equipped) • Connect the Yellow wire to the constant wire of the aftermarket radio. The GMLAN29-100 comes set up for amplified systems. If the vehicle is not amplified disconnect the 4 pin harness located between the 30 way and 22 way connector. Connect the supplied 4 pin speaker harness and connect the following: • Connect the Violet wire to the right rear positive wire of the aftermarket radio • Connect the Violet/Black wire to the right rear negative wire of the aftermarket radio • Connect the Green wire to the left rear positive wire of the aftermarket radio • Connect the Green/Black wire to the left rear negative wire of the aftermarket radio INSTALLING THE GMLAN29-100 With all the connections completed, plug the 20, 22, and 8 pin harnesses into the GMOS-100i (sold separately). • Reconnect the negative battery terminal. • Plug the 30 pin GM harness into the vehicle side harness, and plug the aftermarket radio harness into the aftermarket radio. • Cycle the key by turning the ignition on then back off, then back on again to test the radio. 1 PROGRAMMING SWC • Turn on the ignition • The LED will begin to blink rapidly • Turn on the aftermarket radio • Press volume up until radio responses TESTING THE GMLAN29-100 • Turn the ignition on, and then turn the aftermarket radio on. • Push the Onstar button, the radio should turn off (radio will mute if mute wire is connected) and you should hear Onstar. Push the Onstar cancel button and the radio should come back on. 2 NOTES NOTES INSTALLATION INSTRUCTIONS FOR PART GMLAN29-100 REV. 4/2/2010 1-800-221-0932 axxessinterface.com © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION ...