Assessments - 6, GPA: 3.8
(
)
)
|
Facilidade de uso
2. Connect a speaker to each channel output using Speakon®, Banana Plugs, or bare wire. Factory Preset #2: BRIDGE Putting the amplifier in BRIDGE (bridge-mono) mode delivers the power of both amp channels into a single 8 or 4 ohm load. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation. Before you get started ensure that you: 1. Connect signal source to Channel 1 and Channel 2 using XLR connectors (the amplifier inputs will automatically be summed together when selecting this preset). 2. Connector the speaker as shown. a. If using the binding post outputs, connect the positive terminal of the speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2. b. If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only. Follow these quick steps to configure the amplifier for BRIDGE operation: 1. Push the “Set/Enter” button and you will see the word “Preset” flashing. 2. Push the “Set/Enter” button again to enter the list of presets in the amplifier. 3. Push the “Next/Down” or “PREV/UP” button until the screen displays “Bridge”. 4. Push the “Set/Enter” button to confirm your selection. 5. The display will now read “Bridge” with the Y icon and Bridge icon highlighted. Get Started XTi 6002 back panel shown. See page 9 for XTi 1002, 2002 and 4002 back panel. NOTE: Custom wiring should only be performed by qualified personnel. WARNING: Before you start to set up your amplifier, make sure you read and observe the Important Safety Instruc tions found at the beginning of this manual. XTi2 Series Power Amplifiers Operation Manual page 5 Get Started Factory Preset #3: XOVER Putting the amplifier in XOVER mode enables a 1.2kHz 4th order (24dB/octave) filter that sends frequencies of 1.2kHz and below to Channel 1 output and frequencies of 1.2kHz and above to Channel 2 output. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation. Before you get started ensure that you: 1. Connect signal source to Channel 1 ONLY using an XLR connector (the amplifier inputs will automatically be put into Y mode when selecting this preset). 2. Connector the speaker as shown. a. Connect the speaker you wish to receive the low and mid frequencies (1.2kHz and below) to Channel 1 output using Speakon®, Banana Plugs, or bare wire. b. Connect the speaker you wish to receive the high frequencies (1.2kHz and above) to Channel 2 output using Speakon®, Banana Plugs, or bare wire. Follow these quick steps to configure the amplifier for XOVER operation: 1. Push the “Set/Enter” button and you will see the word “Preset” flashing. 2. Push the “Set/Enter” button again to enter the list of presets in the amplifier. 3. Push the “Next/Down” or “PREV/UP” button until the screen displays “BIAMP”. 4. Push the “Set/Enter” button to confirm your selection. 5. The display will now read “BIAMP” with the Y icon and XOV icon highlighted. LOW 1+/– HIGH 2+/– Factory Preset #4: BRG SUBS Putting the amplifier in BRG SUBS (bridged subs) mode allows you to bridge the amplifier for use with a single 8 or 4 ohm subwoofer. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) LowPass filter is enabled, and the output mode is put into bridge-mono mode. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation. Before you get started ensure that you: 1. Connect signal source to Channel 1 and Channel 2 using XLR connectors (the amplifier inputs will automatically be summed together when selecting this preset). 2. Connector the speaker as shown. a. If using the binding post outputs, connect the positive terminal of the speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2. b. If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only. Follow these quick steps to configure the amplifier for XOVER operation: 1. Push the “Set/Enter” button and you will see the word “Preset” flashing. 2. Push the “Set/Enter” button again to enter the list of presets in the amplifier. 3. Push the “Next/Down” or “PREV/UP” button until the screen displays “XOVER”. 4. Push the “Set/Enter” button to confirm your selection. 5. The display will now read “XOVER” with the Y icon and XOV icon highlighted. XTi2 Series Power Amplifiers page 6 Operation Manual Factory Preset #5: SUBSYNTH Putting the amplifier in SUBSYNTH mode allows you to turn on the SubHarmonic Synth feature for use with a subwoofer on both channels. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) filter is enabled on both Channel 1 and Channel 2, and the SubHarmonic Synth fe...
Este manual também é adequado para os modelos :Avtousiliteli - XTI2 SERIES XTI 1002 (6.44 mb)
Avtousiliteli - XTI2 SERIES XTI 4002 (6.44 mb)
Avtousiliteli - XTI2 SERIES XTI 6002 (6.44 mb)