Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
There are two sets of terminals to make it easy to connect multiple woofers. Either set of (+/–) terminals may be used when connecting woofers. To the right are two application diagrams to help plan your subwoofer system installation. Figures 4 and 5 show how to configure the CS300.1 subwoofer amplifier. NOTE: For simplicity, Figures 4 and 5 do not show power, remote and input connections. NOTE: Minimum speaker load is 2 ohms total. Figure 4. CS subwoofer amplifier with two woofers connected. Figure 5. CS subwoofer amplifier with one woofer connected. APPLICATIONS – CS60.4 The CS60.4 can be set up for stereo 4-channel, 3-channel or bridged 2-channel operation, as shown in Figures 6 through 8. NOTE: For simplicity, Figures 6 through 8 do not show power, remote and input connections. NOTE: Minimum speaker impedance for stereo operation is 2 ohms. Minimum speaker impedance for bridged operation is 4 ohms. Figure 6. CS60.4 amplifier in 4-channel (stereo) operation to drive front and rear full-range speakers. Rear RightRear LeftFront RightFront Left Rear RightRear LeftFront RightFront Left Figure 7. CS60.4 is set up for 3-channel operation to drive a set of full-range speakers and a subwoofer. Front RightFront Left Figure 8. CS60.4 used in bridged 2-channel mode to drive a set of components or subwoofers. Set crossovers according to application. Front RightFront Left APPLICATIONS – CS60.2 Figure 9. CS60.2 used in 2-channel (stereo) operation to drive a set of full-range speakers. RightLeft RightLeft Figure 10. CS60.2 used in bridge mode to drive a subwoofer. CONTROLS AND SETUP TROUBLESHOOTING SETTING THE SETTING INPUT SYMPTOM LIKELY CAUSE SOLUTION CROSSOVER(S) Determine your system plans and set the crossover mode switch accordingly. If your system design does not include a subwoofer with the CS60.4, set the crossover mode to FLAT and skip to “Setting Input Sensitivity.” Initially set the crossover frequency control midway. While listening to music, adjust the crossover for the least perceived distortion from the speakers, allowing them to reproduce as much bass as possible. SENSITIVITY 1. Initially turn the INPUT LEVEL control(s) to minimum (counter clockwise). 2. Reconnect the (–) negative lead to the vehicle’s battery. Apply power to the audio system and play a dynamic music track. 3. On the source unit, increase the volume control to 3/4 volume. Slowly increase the INPUT LEVEL control(s) toward three o’clock until you hear slight distortion in the music. Then reduce the INPUT LEVEL slightly until distortion is no longer heard. No audio No voltage at BATT+ Check voltages at (POWER LEDs or REM terminals, amplifier terminals are off) or bad or no ground with VOM connection No audio Amplifier is (POWER overheated LEDs are on) Voltage more than 16V or less than 8.5V on BATT+ connection Make sure amplifier cooling is not blocked at mounting location; verify speaker-system impedance is within specified limits Check vehicle charging system Systems using a separate subwoofer set the crossover mode to HP (high pass) for your full-range speakers. Adjust the crossover frequency to limit bass and provide increased system volume with less distortion. No audio Voltage less than 9V on Check vehicle NOTE: After the source unit is on, blue (POWER BATT+ connection charging system LEDs (on the top panel) will light, indicating LEDs flash) the amplifier is on. If not, check the wiring, DC voltage on Amplifier may need especially the remote connection from the amplifier output service;...
Este manual também é adequado para os modelos :Avtousiliteli - CS300.1 (691.25 kb)
Avtousiliteli - CS60.4 (691.25 kb)