Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Signal ground must be connected to a chassis ground. WHITE (+) Left Channel WHITE/BLACK (-) Left Channel BLACK (-) Signal Ground GRAY/BLACK (-) Right Channel GRAY (+) Right Channel © 2005 Directed Electronics, all rights reserved Speaker Connections HP-2800 One Channel/Two Channel Configuration The Orion HP-2800 amplifier offer two positive and two negative output terminals for ease of connecting channel 1 and/or 2 outputs to the speakers. The amplifier is stable to 2W. See diagrams below. . Lowest recommended impedance is 2W stereo. . Outputs can be configured for high-pass, low-pass, or full range operation. SPEAKER SPEAKER BRIDGE BRIDGE 1CH + 1CH 2CH + 2CH --1CH + 1CH -2CH + 2CH CHANNEL 1 CHANNEL 1 CHANNEL 2 Bridge Configuration Bridging allows one speaker to be driven at a higher power level from the amplifier. SPEAKER BRIDGE 1CH + 1CH -2CH + 2CH BRIDGED © 2005 Directed Electronics, all rights reserved Three Channel (Channel 1, Channel 2, Bridged) . Channels 1 and 2 are configured for two-channel stereo operation. . Front channel lowest recommended impedance is 2W stereo. . The third output is configured for a single channel bridged output. . The bridged outputs lowest recommended impedance is 4W. . Outputs are configured for high-pass, low-pass, or full range operation. SPEAKER BRIDGE 1CH + 1CH -2CH + 2CH © 2005 Directed Electronics, all rights reserved Speaker Connections HP-4800 The Orion HP-4800 amplifier offer four positive and four negative output terminals for ease of connecting channel 1, 2, 3, and 4 outputs to the speakers. The amplifier is stable to 2W. See diagrams below. Four Channel Stereo Configuration . Channel 1/2 and channel 3/4 lowest recommended impedance is 2W stereo. . Crossover mode, output, and gain configurations are independently adjustable between the front and rear channels. . Two-channel or four-channel input can be used for this configuration. For source unit fading, use the four-channel input mode. . Channels 1/2 and channels 3/4 outputs can be individually configured for high- pass, low-pass, or full range operation. SPEAKER SPEAKER +1CH +2CH-1CH -2CH BRIDGE +3CH +4CH-3CH -4CH BRIDGE CHANNEL 2CHANNEL 1CHANNEL 4CHANNEL 3 © 2005 Directed Electronics, all rights reserved Three Channel Stereo/Bridged Configuration . Channels 1/2 are configured for 2-channel stereo operation. . Channel 1/2 lowest recommended impedance is 2W stereo. . Channels 3/4 are configured for a single channel bridged output. . Channel 3/4 lowest recommended impedance is 4W. . Crossover mode, output, and gain configurations are independently adjustable between channels 1/2 and 3/4. . Two-channel or four-channel input can be used for this configuration. For source unit fading, use the four-channel input mode. . Channel 1/2 and 3/4 outputs can be configured for high-pass, low-pass, or full range operation. . Channel 3/4 outputs are configured for summed bridged operation for subwoofer. SPEAKER SPEAKER +1CH +2CH-1CH -2CH BRIDGE +3CH +4CH-3CH -4CH BRIDGE CHANNEL 2CHANNEL 1BRIDGED © 2005 Directed Electronics, all rights reserved Tri-Mode Six Channel Configuration . Lowest recommended impedance is 2W stereo and 4W bridged mono. . Front and rear outputs must be set for full range operation. . Passive crossovers must be used on all components and frequencies must not overlap. WARNING! Failure to observe these requirements may result in damage to the amplifier. SPEAKER SPEAKER BRIDGE BRIDGE 1CH + 1CH -2CH + 2CH -3CH + 3CH -4CH + 4CH © 2005 Directed Electronics, all rights reserved AMPLIFIER INSTALLATION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low profile size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance. Always mount the amplifier in a place that protects the amplifier from the elements. In addition, mount the amplifier on a stable, flat surface. NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown. WARNING! Do not mount any amplifier in the engine compartment. Amplifiers are not designed to endure the harsh environment of the exterior elements. Passenger Compartment If you are going to mount the amplifier in the passenger compartment, make sure you have adequate room for ventilation. The amplifiers have been designed to make under-seat mounting possible. When mounting your amplifier under a seat or similar area, keep a minimum of 1" of clearance around the amplifier for adequate cooling. Trunk Compartment Mounting your amplifier in the trunk provides excellent performance as long as you do not restrict the airflow around the heatsink of the amplifier. For optimal results, mount the amplifier with as much clearance as possible. This type of mounting will yield the best cooling due to the convection effect of the amplifier chassis. General Precautions and Installation Tips WARNING! Be careful not to cut or drill into gas tank...
Este manual também é adequado para os modelos :Avtousiliteli - HP-2800 (616.18 kb)