Assessments - 2, GPA: 5 ( )

Fabricante : Ashly Arquivo Tamanho: 1.97 mb Arquivo Nome : Língua de Ensino:

Signal LED not lit Make sure the signal source is operating and try another cable. Check position of Volume Pots. Signal LEDs responding to signal level Check the speaker wiring for breaks. Try another speaker and cable. Protect LED is lit Overheating will cause protective muting. Check for proper ventilation. Check the mode indicators on the back panel and make sure the mode selector on the rear panel is in the stereo position. Make sure other equipment in the signal path such as mixers and preamps are set for stereo, not mono Distorted Sound Power LED is lit A faulty speaker or a loose connection could cause this. Check the wiring and try another speaker. Signal LEDs responding to signal level The signal source might be clipping. Keep the volume pots at least halfway up so that the source does not have to be overdriven. Clip LEDs not lit Keep the volume pots at least halfway up and try changing input sensitivity with the gain selector on the rear. Unplug the amplifier input to confirm that the hiss is coming from the source or from a device upstream. Erratic or popping noises indicate an electronic fault in the offending unit. To keep the noise floor low, operate the primary signal source at full level, without clipping. Avoid boosting the signal further between the source and the amplifier. Squeals and Squeals and Feedback Microphone feedback should be eliminated Feedback with mixer controls. If noise continues to build up with no microphone gain, there is a serious fault in the signal processors or cables. Working in succession from the signal source towards the amplifier and check each device in the signal path by reducing its gain or by unplugging it. Copyright© 2011 – Ashly Audio Inc. Operator Manual – KLR Series Amplifiers Page - 11 Specification Table KLR 5000 600W 1100W 1400W 1700W X 800W X X Important Safety Instructions – 2 Introduction - 3 The KLR Series - 4 Physical Description - 5 Installation – 6 Troubleshooting - 10 Spec Table – 11 Warranty - 12 Stereo Mode, both channels driven 1000W 4., 20Hz - 20kHz, 1% THD 70V Output, 20Hz - 20kHz, 1% THD, per channel 2500W 5000W Idle (120VAC 60Hz) * 1/3 Power Sine Wave (120VAC 60Hz) * 17.5A 215 3111 4395 1.4V, 32B, 26dB Signal to Noise Ratio (20Hz-20kHz, rated power @ 8. unweighted) Frequency Response 1W @ 8. 20Hz-20kHz (-3dB down point) 0.99A 0.92A 1.05A 1.14A 14.9A 16.6A 19.8A 24.7A >110 dB 2 Step Class H +/- 0.3dB 5Hz – 70kHz > 380 <0.05% 12 k., balanced 12dB/Oct Output Overcurent, DC Output, Chassis Temperature, Mains Breaker (KLR-5000 uses Internal Mains Fuse Instead of Breaker) Variable Speed Fan, Front to Rear Air Flow Prot/Clip, Signal, Power Per channel: front panel 3- Pin Euroblock, XLR, .” TRS Phone Jack Four pin Speakon type Temperature: -10C - +40C / Humidity: 0% - 90% 3-Prong NEMA 5-15 (5-20 for KLR-5000) 19” x 3.5” x 16” (482mm x 88mmx x407mm) Weight 24 lbs (10.9kg) 26.4 lbs (12kg) 26.7 lbs (12.1kg) 28.2 lbs (12.8kg) * For 230VAC 50Hz models, divide Line Current Draw values by 2. All Specifications Subject to Change or Improvement Without Notice. All Rights Reserved r0611 Page - 12 Operator Manual – KLR Series Amplifiers Important Safety Instructions – 2 Introduction - 3 The KLR Series - 4 Physical Description - 5 Installation – 6 Troubleshooting - 10 Spec Table - 11 Warranty - 12 Ashly Audio Inc. LIMITED WARRANTY (USA ONLY) (Other countries please contact your respective distributor or dealer.) For units purchased in the USA, warranty service for this unit shall be provided by ASHLY AUDIO, INC. in accordance with the following warranty statement. ASHLY AUDIO, INC. warrants to the owner of this product that it will be free from defects in workmanship and materials for a period of FIVE years from the original-date-of-purchase. ASHLY AUDIO INC. will without charge, repair or replace at its discretion, any defective product or component parts upon prepaid delivery of the product to the ASHLY AUDIO, INC. factory service department, accompanied with a proof of original-date-of-purchase in the form of a valid sales receipt. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. EXCLUSIONS: This warranty does not apply in the event of misuse, neglect, or as a result of unauthorized alterations or repairs made to the product. This warranty is void if the serial number is altered, defaced, or removed. ASHLY AUDIO, INC. reserves the right to make changes in design, or make additions to, or improvements upon, this product without any obligation to install the same on products previously manufactured. Any implied warranties, which may arise under the operation of state law, shall be effective only for FIVE years from the original-date-of-purchase of the product. ASHLY AUDIO, INC. shall be obligated to only correct defects in the product itself. ASHLY AUDIO, INC. is not liable for any damage or injury, which may result from, or be incidental to, or a consequence of, such defects. Some states ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :