Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
i REMOTE LEVEL CONTROL • External remote controller for volume level control. j POWER (GND/REM/+12V) • Connect +12V DC power cable, ground wire and remote wire. k Fuse: 30Ax2 l SPEAKER OUTPUT • Connect to subwoofers. 3. Installation Installation C You can mount the amplifier either under a seat or on the rear tray. Note •• To avoid interference, do not place the amplifier too close to the car audio or antenna. •• The supplied mounting screws are 25mm long. Make sure that the mounting board is thicker than 25mm. 1 Place the unit on the location for installation. 2 Mark the positions of the four screw holes. 3 Drill the holes with driller of approximately 4mm in diameter. 4 Mount the unit with the supplied screws. Connect speakers D Note •• Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a bridged amplifier). •• Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may degrade sound quality. Option 1: Mono bridged mode: connect 1 speaker a Option 2: Stereo mode: connect 2 speakers b Connect car audio E Option 1: High level input connection a Connect the amplifier to your car audio with the supplied High level input connector. Option 2: Line input connection b Connect the amplifier to the car audio with a RCA cable (not supplied). Connect power F 1 Make the power connection as illustrated below: • Connect the ground wire from the car to the GND socket. • Connect the remote wire from the car audio to the REM socket. v With this connection, you can turn on/off the amplifier with the car audio. • Connect the power wire from the car battery to the +12V socket. Tip •• If your car audio does not have remote output, connect the remote input terminal (REM) to the accessory power supply. 4. Use your power amplifier Adjust input level You can adjust the input voltage from 0.3V to 6V. 1 Rotate INPUT LEVEL to adjust input voltage. Adjust bass boost You can punch extra bass for 0 to 12dB. 1 Rotate BASS BOOST to punch for extra bass. About the protector indicator The amplifier has a built-in protection circuit to protect the transistors and speakers when: • The unit is overheated. Or • A DC current is generated. Or • The battery voltage is over low or over high. Or • The speaker terminals are short circuited. When the PROTECT indicator lights up in red, the unit shuts down automatically. If this happens, please: 1 Take out the disc or tape and turn off the car audio. 2 Check the cause of the malfunction (see above). 3 If the amplifier has overheated, wait until the unit cools down before use. Adjust subwoofer frequency Rotate Subwoofer to adjust low-pass-f ilter frequency for subwoofer. 1 Rotate SUBWOOFER to adjust frequency: 30Hz to 320Hz. Turn subsonic f ilter on or off 1 Slide SUBSONIC to ON position. • The subsonic is turned on, frequency below 15Hz is f iltered. • To turn off the subsonic filter, slide SUBSONIC ON/OFF to OFF position. Adjust volume G You can adjust volume at the front seat via the supplied volume control. 1 Connect the supplied volume controller to the REMOTE LEVEL CONTROL socket. 2 Rotate the volume knob to adjust volume. Replace fuse H If there is no power, the fuse may be damaged and need to be replaced. 1 Pull out the damaged fuse. 2 Replace the fuse with the supplied fuses or to buy two fuses that matches the voltage of the damaged fuse (30Ax2). If the fuse gets damaged immediately after it has been replaced, there may be an internal malfunction. In such case, consult your Philips dealer. 5. Product information Note •• Product information is subject to change without prior notice. Power Output (RMS) - 4 ohm - 2 ohm 250Wx1 400Wx1 Total harmonic distortion 0.08% Signal to noise ratio 105dB Frequency response 5-320Hz Input sensitivity 300mV-6V Input impedance 22k ohm Fuse rating 30Ax2 Dimensions (DxWxH) 54.4x336.5x240.2mm Русский Русский Внесение любых изменений, которые должным образом не разрешены c INPUT LEVEL 1 Разместите устройство в месте установки. • Подключите провод дистанционного управления от 6.Troubleshooting Philips Consumer Lifestyle, может привести к лишению пользовател я права • Переключение напряжения на входе (0,3 В до 6 В). автомобильной аудиосистемы к разъему REM. 2 Отметьте 4 места крепления болтов. управлять оборудованием. To keep the warranty valid, never tr y to repair the system yourself. d BASS BOOST v Данное подключение позволяет включать и выключать 3 Просверлите отверстия для крепления болтов диаметром 1. Важно! If you encounter problems when using this apparatus, check the усилитель через автомобильную аудиосистему. © Koninklijke Philips Electronics N.V., 2009 Все права защищены. • Усиление частот в районе 45 Гц до максимальной около 4 мм. following points before requesting ser vice. If the problem remai мощности 12 дБ. • Подключите кабель питания от автомобильного аккумулятора к разъему +12 В. ns Характеристики мог ут быть изменены без предварительного уведомления. Торговые марки 4 Закрепите устройство с помощью болтов (входя...