Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
What’s in the box A Check and identify the contents of your package: a Amplifier b Screw_4x25mm (x4) c Fuse (x2) d Hi input connector (x1) Overview of the main unit B a OUTPUT L/R • Connect additional amplifier for additional speakers. b INPUT L/R • Connect car audio with RCA cable. c HI INPUT • Connect car audio with the supplied high input connector. d INPUT LEVEL • Adjust input level (0.3V to 6V). e PROTECT • Light in red when the PROTECTOR is activated. f POWER • Light in blue when power is turned on. g FREQ • Adjust frequency of HPF or LPF from 30Hz to 400Hz. h HPF/OFF/LPF • Select High-pass-filter (HPF), Low-pass-filter(LPF) or OFF (flat) mode. i BASS BOOST • Boost the frequencies at around 45Hz to a maximum of 12dB. j POWER (GND/REM/+12V) • Connect +12V DC power cable, ground wire and remote wire. k Fuse: 30Ax2 l SPEAKER OUTPUT • Connect to speakers or subwoofers. 3. Installation Installation C You can mount the amplifier either under a seat or on the rear tray. Note •• To avoid interference, do not place the amplifier too close to the car audio or antenna. •• The supplied mounting screws are 25mm long. Make sure that the mounting board is thicker than 25mm. 1 Place the unit on the location for installation. 2 Mark the positions of the four screw holes. 3 Drill the holes with driller of approximately 4mm in diameter. 4 Mount the unit with the supplied screws. Connect speakers D Note •• Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a bridged amplifier). •• Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may degrade sound quality. Option 1: Mono bridged mode: connect 1 speaker a Option 2: Stereo mode: connect 2 speakers b Option 3: Tri-mode: connect 3 speakers c Connect car audio E Option 1: High level input connection a Connect the amplifier to your car audio with the supplied High level input connector. Option 2: Line input connection b Connect the amplifier to the car audio with a RCA cable (not supplied). Option 3: Line output connection c Connect the amplifier to another amplifier. Connect power F 1 Make the power connection as illustrated below: • Connect the ground wire from the car to the GND socket. • Connect the remote wire from the car audio to the REM socket. v With this connection, you can turn on/off the amplifier with the car audio. • Connect the power wire from the car battery to the +12V socket. Tip •• If your car audio does not have remote output, connect the remote input terminal (REM) to the accessory power supply. 4. Use your power amplifier Select crossover frequency mode You can select crossover frequency mode as below: HPF (high-pass-filter) mode Select this mode when mid-range speakers and tweeters are connected for high frequency output. LPF (Low-pass-filter) mode Select this mode when woofer and subwoofer is connected for low frequency output. OFF (flat) mode Select this mode when tri-mode speaker connection is used. 1 Slide HPF/OFF/LPF to the selected positon. Adjust frequency You can adjust frequency of HPF or LPF from 30HZ to 400Hz. Note ••When the HPF/OFF/LPF switch is set at OFF position, the frequency adjustment does not work. 1 Rotate FREQ to select frequency. Adjust input level You can adjust the input voltage from 0.3V to 6V. 1 Rotate INPUT LEVEL to adjust input voltage. Adjust bass boost You can punch extra bass for 0 to 12dB. 1 Rotate BASS BOOST to punch for extra bass. About the protector indicator The amplifier has a built-in protection circuit to protect the transistors and speakers when: • The unit is overheated. Or • A DC current is generated. Or • The battery voltage is over low or over high. Or • The speaker terminals are short circuited. When the PROTECT indicator lights up in red, the unit shuts down automatically. If this happens, please: 1 Take out the disc or tape and turn off the car audio. 2 Check the cause of the malfunction (see above). 3 If the amplifier has overheated, wait until the unit cools down before use. Replace fuse G If there is no power, the fuse may be damaged and need to be replaced. 1 Pull out the damaged fuse. 2 Replace the fuse with the supplied fuses or to buy two fuses that matches the voltage of the damaged fuse (30Ax2). If the fuse gets damaged immediately after it has been replaced, there may be an internal malfunction. In such case, consult your Philips dealer. 5. Product information Note •• Product information is subject to change without prior notice. Power Output (RMS) - 4 ohm - 4 ohm (bridged) - 2 ohm 125Wx2 380Wx1 190Wx2 Total harmonic distortion 0.01% Signal to noise ratio 106dB Channel separation 50dB Frequency response 5-100kHz Input sensitivity 300mV-6V Input impedance 22k ohm Fuse rating 30Ax2 Dimensions (DxWxH) 54.4x336.5x240.2mm a b c d a j k l ihgfed c b L R L R 4 ohm speaker Динамик 4 Ом L R 4 ohm speaker 4 ohm speaker Динамик 4 Ом Динамик 4 Ом 8 ohm speaker Динамик 8 Ом L R 4 ohm speaker Динамик 4 Ом 4 ohm speaker Динамик 4 Ом Left speaker Right speaker Car ...