Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
© 2005 Directed Electronics, Inc. all rights reserved PARALLEL SYNCED GAIN CONNECTIONS/SETTINGS Refer to figure 5 for wiring details. 1. I IIn nnp ppu uut tt S SSi iig ggn nna aal ll - Connect these RCA jacks as described in the Front Panel Connectionsection of this guide. 2. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh • Set the slave/master switch on the master amplifier to the MASTER position. • Set the slave/master switch on the slave amplifier to the SLAVE position. • Setting the slave/master switch on both amplifiers will automatically set the I/O RCA jack configuration according to each amplifier’s slave or master designation. N NNO OOT TTE EE: ::One master amplifier can control up to three slave amplifiers in this combination. Multiple identical master/slave combinations can be added to any given system. 3. P PPh hha aas sse ee S SSw wwi iit ttc cch hh - --Set the phase switches of all synced amps to the same position (all at 0° or all at 180°). 4. In order to achieve safe, optimal performance, the LPF, Bass EQ, and Subsonic Filter controls on all synced amps must be set to the same position. 5. S SSi iig ggn nna aal ll C CCo oon nnn nne eec cct tti iio oon nn - Connect an RCA cable between the OUT RCA jack of the master amplifier and the SLAVE IN RCA jack of the slave amplifier as shown in the Figure 5. 6. S SSu uub bbw wwo ooo oof ffe eer rr S SSp ppe eea aak kke eer rr C CCo oon nnn nne eec cct tti iio oon nn - In this amplifier combination each amplifiers must drive its own separate subwoofer(s). Connect the speaker terminals of each amplifier to any combination of one or more subwoofers that results in nominal impedance between one and four ohms. Make sure that each amplifier sees the same speaker impedance. W WWA AAR RRN NNI IIN NNG GG: ::The amplifier’s gain control is bypassed completely in SLAVE mode. Do N NNO OOT TT move the MASTER/SLAVE switch to SLAVE position when the amplifier is connected and playing. Do N NNO OOT TT connect any signal source to the amplifier in SLAVE mode that exceeds 200mV. © 2005 Directed Electronics, Inc. all rights reserved FIGURE 5—PARALLEL SYNC GAINED D1200/D2400 . . Subwoofer Wiring (top view) MASTER SLAVE N NNO OOT TTE EE: ::The dual + and -- sub-out terminals are paralleled internally and the combined load impedance should be taken into consideration when connecting multiple subwoofers. © 2005 Directed Electronics, Inc. all rights reserved EXTERNAL SYNCED BRIDGED CONNECTIONS/SETTINGS 1. I IIn nnp ppu uut tt S SSi iig ggn nna aal ll - Connect these RCA jacks as described in the Front Panel Connection section of this guide. 2. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh • Set the slave/master switch on the master amplifier to the MASTER position. • Set the slave/master switch on the slave amplifier to the SLAVE position. • Setting the slave/master switch on both amplifiers will automatically set the I/O RCA jack configuration according to each amplifiers slave or master designation. N NNO OOT TTE EE: ::Amplifiers in this combination can only be connected in matched pairs. Multiple matched pairs may be added to drive separate subwoofer loads in a given system. 3. P PPh hha aas sse ee S SSw wwi iit ttc cch hh - Set the phase switches of all synced MASTER amps to 0°. Set the phase switches of all synced SLAVE amps to 180°. The master and slave amps must be set to the opposite phase mode in order for External Synced Bridged operation to work. 4. In order to achieve safe, optimal performance, the LPF, Bass EQ, and Subsonic Filter controls on all synced amps must be set to the same position. 5. S SSi iig ggn nna aal ll C CCo oon nnn nne eec cct tti iio oon nn - Connect an RCA cable between the OUT RCA jacks of the Master amplifier and the INPUT RCA jack of the Slave amplifier as shown in Figure 6. 6. S SSu uub bbw wwo ooo oof ffe eer rr S SSp ppe eea aak kke eer rr C CCo oon nnn nne eec cct tti iio oon nn - In this amplifier combination the Subwoofer speaker terminals of both amplifiers drive common subwoofer(s). Use the following speaker connection diagram when connecting the subwoofers to the amplifiers. Connect the amplifiers speaker terminals to any combination of one or more subwoofers that results in a nominal impedance between 2 and 4 ohms. DO NOT connect loads of less than 2 ohms when connecting to amplifiers in the External Synced Bridged combination. W WWA AAR RRN NNI IIN NNG GG: ::Two wires of 12AWG minimum must be connected between the negative sub out terminals of the master and slave amplifiers. W WWA AAR RRN NNI IIN NNG GG: ::The amplifier’s gain control is bypassed completely in SLAVE mode. Do N NNO OOT TT move the MASTER/SLAVE switch to SLAVE position when the amplifier is connected and playing. Do N NNO OOT TT connect any signal source to the amplifier in SLAVE mode that exceeds 200mV. © 2005 Directed Electronics, Inc. all rights reserved FIGURE 5—EXTERNAL SYNCED BRIDGE . ...
Este manual também é adequado para os modelos :Avtousiliteli - D2400 (493.96 kb)